544296

Bosch LR 1 Manual

19
Zoom out
Zoom in
Previous page
1/261
Next page
English | 19
Bosch Power Tools 2 609 141 177 | (31.3.14)
Working Advice
Marking
When the laser beam runs through the centre of the reception area 6, its height can
be marked at the centre mark 5 right and left on the measuring tool. The centre mark
is located 45 mm away from the top edge of the measuring tool.
Aligning with the Spirit Level
The measuring tool can be aligned vertically (plumb line) with the spirit level 8. A
measuring tool applied out-of-level leads to faulty measurements.
Attaching with the Holder (see figure A)
With the holder
17
, the measuring tool can be fastened to a construction laser measur-
ing rod
15
(accessory) as well as to other auxiliary tools with a width of up to 65 mm.
– Screw the holder 17 to the retainer opening 12 on the rear side of the measuring
tool with fastening screw 16.
– Loosen the locking screw 13, slide the holder onto the construction laser measur-
ing rod 15, for example, and retighten the locking screw 13.
The upper edge 14 of the holder is located at the same height as the centre mark 5
and can be used for marking of the laser beam.
Attaching with the Magnet (see figure B)
When a positive-lock attachment is not absolutely required, the measuring tool can be
attached to steel parts via the face side using the magnet plate 4.
Maintenance and Service
Maintenance and Cleaning
– Keep the measuring tool clean at all times.
– Do not immerse the measuring tool in water or other fluids.
– Wipe off debris using a moist and soft cloth. Do not use any cleaning agents or sol-
vents.
After-sales Service and Application Service
In all correspondence and spare parts orders, please always include the 10-digit arti-
cle number given on the type plate of the measuring tool.
Our after-sales service responds to your questions concerning maintenance and re-
pair of your product as well as spare parts. Exploded views and information on spare
parts can also be found under:
www.bosch-pt.com
OBJ_BUCH-780-005.book Page 19 Monday, March 31, 2014 9:28 AM
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch LR 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch LR 1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info