Manual Bosch gws 1400 professional (page 23 of 301) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

391343

Zoom out

Zoom in

1/301

24 | English 1 609 929 K94 • 20.12.06

Approved Grinding Tools

All grinding tools mentioned in these operating

instructions can be used.

The permissible speed [rpm] or the circumferential

speed [m/s] of the grinding tools used must at least

match the values given in the table.

Therefore, observe the permissible rotational/cir-

cumferential speed on the label of the grinding tool.

Rotating the Machine Head

f Before any work on the machine itself, pull

the mains plug.

The machine head can

be rotated with

respect to the

machine housing in

90° steps. In this man-

ner, the On/Off switch

can be brought into a

more convenient posi-

tion for special work-

ing situations, e.g., for

cutting operations

using the cutting guide

with dust extraction

protection guard

19/cut off stand or for

left-handed persons.

Completely unscrew the four screws. Rotate the

machine head carefully, without removing it from

the housing, to the new position. Screw in and

tighten the four screws again.

Operation

Starting Operation

f Observe correct mains voltage! The voltage

of the power source must agree with the

voltage specified on the nameplate of the

machine. Power tools marked with 230 V can

also be operated with 220 V.

When operating the machine with power from mobile

generators that do not have sufficient reserve capacity

or are not equipped with suitable voltage control with

starting current amplification, loss of performance or

untypical behavior can occur upon switching on.

Please observe the suitability of the power generator

being used.

Switching On and Off

To start the power tool, push the On/Off switch 3 for-

wards.

To lock the On/Off switch 3, press the On/Off switch

3 down at the front until it latches.

To switch off the power tool, release the On/Off

switch 3 or, if it is locked, briefly push down the back

of the On/Off switch 3 and then release it.

f Check grinding tools before using. The

grinding tool must be mounted properly and

be able to move freely. Carry out a test run

for at least one minute with no load. Do not

use damaged, out-of-centre or vibrating

grinding tools. Damaged grinding tools can

burst and cause injuries.

Reduced starting current (GWS 1400)

The electronic reduced starting current limits the

power consumption when switching the tool on and

enables operation from a 13 ampere fuse.

Constant Electronic Control (GWS 1400)

Constant electronic control holds the speed constant

at no-load and under load, and ensures uniform work-

ing performance.

Operating Instructions

f Exercise caution when cutting slots in struc-

tural walls; see Section “

Information on

Structures

”.

f Clamp the workpiece if it does not remain

stationary due to its own weight.

f Do not strain the machine so heavily that it

comes to a standstill.

f Grinding and cutting discs become very hot

while working; do not touch until they have

cooled.

max.

[mm] [mm]

D b d [rpm] [m/s]

115

125

22.2

11000

115

125

––

11000

75 30 M 14 11000 45

OBJ_BUCH-310-001.book Page 24 Wednesday, December 20, 2006 9:31 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch gws 1400 professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 14,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch gws 1400 professional Manual

Product: