Manual Bosch GLM 80 (page 25 of 319) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

544344

Zoom out

Zoom in

1/319

English | 25

Bosch Power Tools 1 609 92A 0KB | (25.4.14)

To recall the stored measurements, press

button 7. The result of the last measure-

ment is indicated on the display, along

with the indicator for the measured-value

list e and the memory location of the dis-

played measurements.

When no further measurements are stored after pressing but-

ton 7 again, the measuring tool switches back to the last

measuring function. To exit the measured-value list, press

one of the measuring-mode buttons.

To continuously save the currently displayed length measure-

ment value as a constant, press and hold the measured-value

list button 7 until “CST” is indicated on the display. A meas-

ured-value list entry cannot be subsequently saved as a con-

stant.

To use a length measurement value in a measuring mode (e. g.

area/surface measurement), press the measured-value list

button 7, select the desired entry and confirm by pressing the

result button 6.

Deleting Measured Values

Briefly pressing button 8 deletes the last individual measuring

value determined in all measuring functions. Briefly pressing

the button repeatedly deletes the individual measured values

in reverse order.

To delete the currently displayed measured-value list entry,

briefly press button 8. To delete the complete measured-val-

ue list and the constant “CST”, press and hold the measured-

value list button 7 and at the same time briefly press button 8.

In wall surface measurement mode, briefly pressing button 8

the first time deletes the last individually measured value;

pressing the button a second time deletes all lengths B

, and

pressing the button a third time deletes all room heights A.

Adding Measured Values

To add measured values, firstly carry out any measurement or

select an entry from the measured-value list. Then press the

plus button 11. For confirmation, “+” appears on the display.

Then carry out a second measurement or select another entry

from the measured-value list.

To call up the sum of both measurements,

press the result button 6. The calculation

is indicated in the measured-value lines a,

and the sum in the result line c.

After calculation of the sum, further mea-

sured values or measured-value list ent-

ries can be added to this result when pressing the plus button

11 prior to each measurement. Pressing the result button 6

ends the addition.

Notes on the addition:

– Mixed length, area and volume values cannot be added to-

gether. For example, when a length and area value are add-

ed, “ERROR” briefly appears on the display after pressing

the result button 6. Afterwards, the measuring tool switch-

es back to the last active measuring mode.

– For each calculation, the result of one measurement is

added (e.g. the volume value); for continuous measure-

ments, this would be the displayed measured value in

result line c. The addition of individual measured values

from the measured-value lines a is not possible.

Subtracting Measured Values

To subtract measuring values, press mi-

nus button 5; For confirmation, “–” is in-

dicated on the display. The further proce-

dure is analog to “Adding Measured

Values”.

Working Advice

General Information

The reception lens 17 and the laser beam outlet 16 must not

be covered when taking a measurement.

The measuring tool must not be moved while taking a meas-

urement (with the exception of the continuous measurement

and grade measurement functions). Therefore, place the

measuring tool, as far as this is possible, against or on a firm

stop or supporting surface.

Influence Effects on the Measuring Range

The measuring range depends upon the light conditions and

the reflection properties of the target surface. For improved

visibility of the laser beam when working outdoors and when

the sunlight is intense, use the laser viewing glasses 27 (ac-

cessory) and the laser target plate 28 (accessory), or shade

off the target surface.

Influence Effects on the Measuring Result

Due to physical effects, faulty measurements cannot be

excluded when measuring on different surfaces. Included

here are:

– Transparent surfaces (e.g., glass, water),

– Reflecting surfaces (e.g., polished metal, glass),

– Porous surfaces (e.g. insulation materials),

– Structured surfaces (e.g., roughcast, natural stone).

If required, use the laser target plate 28 (accessory) on these

surfaces.

Furthermore, faulty measurements are also possible when

sighting inclined target surfaces.

Also, air layers with varying temperatures or indirectly re-

ceived reflections can affect the measured value.

Accuracy Check and Calibration of the Grade Measure-

ment (see figure H)

Regularly check the accuracy of the grade measurement. This

is done by carrying out a reversal measurement. For this,

place the measuring tool on a table and measure the grade.

Turn the measuring tool by 180 ° and measure the grade

again. The difference of the indicated reading may not exceed

by more than 0.3 ° (max.).

In case of greater deviation, the measuring tool must be recal-

ibrated. For this, press and hold the grade measurement but-

ton 3. Follow the directions on the display.

OBJ_BUCH-1347-006.book Page 25 Friday, April 25, 2014 3:28 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GLM 80 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GLM 80 Manual

Product: