Manual Bosch GLM 80 (page 23 of 319) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

544344

Zoom out

Zoom in

1/319

English | 23

Bosch Power Tools 1 609 92A 0KB | (25.4.14)

With exception of the “Permanent laser beam” setting, all ba-

sic settings are retained when switching off.

Continuous Laser Beam

 Do not point the laser beam at persons or animals and

do not look into the laser beam yourself, not even from

a large distance.

In this setting, the laser beam also remains switched on be-

tween measurements; for measuring, it is only required to

press the measuring button 2 once.

Measuring Functions

Simple Length Measurement

For length measurements, press button 12 until the “length

measurement” indication appears on the display.

To switch the laser on and for measuring,

briefly press the measuring button 2 once

each time.

The measured value is displayed in the re-

sult line c.

For several subsequent length measurements, the last mea-

sured results are displayed in the measured-value lines a.

Area Measurement

For area/surface measurements, press button 12 until the in-

dicator for area measurement appears on the display.

Afterwards, measure the length and the width, one after an-

other, in the same manner as a length measurement. The laser

beam remains switched on between both measurements.

Upon completion of the second measure-

ment, the surface is automatically calcu-

lated and displayed in the result line c.

The individual measured values are dis-

played in the measured-value lines a.

Volume Measurement

For volume measurements, press button 12 until the indica-

tor for volume measurement appears on the display.

Afterwards, measure the length, width and the height, one af-

ter another, in the same manner as for a length measurement.

The laser beam remains switched on between all three meas-

urements.

Upon completion of the third measure-

ment, the volume is automatically calcu-

lated and displayed in the result line c.

The individual measured values are dis-

played in the measured-value lines a.

Values above 999999m

cannot be indicated; “ERROR” ap-

pears on the display. Divide the volume to be measured into

individual measurements; their values can then be calculated

separately and then summarized.

Continuous Measurement (Tracking) / Minimum/

Maximum Measurement (see figure B)

For continuous measurements, the measuring tool can be

moved relative to the target, whereby the measuring value is

updated approx. every 0.5 seconds. In this manner, as an ex-

ample, you can move a certain distance away from a wall,

while the actual distance can always be read.

For continuous measurements, press function mode button 4

until the indicator for continuous measurement appears on

the display. To start the continuous measurement, press the

measuring button 2.

The minimum measurement is used to determine the shortest

distance from a fixed reference point. It is used, as an exam-

ple, for determining plumb lines or horizontal partitions.

The maximum measurement is used to determine the greatest

distance from a fixed reference point. It is used, as an exam-

ple, for determining diagonals.

The current measuring value is displayed

in the result line c. The maximal (“max”)

and the minimal (“min”) measuring value

are displayed in the measured-value lines

a. It is always overwritten, when the cur-

rent length measurement value is less

than the present minimal or larger than

the present maximal value.

The previous minimal and maximal values are deleted by

pressing the button for clearing the internal memory 8.

Pressing the measuring button 2 ends the continuous meas-

urement. The last measured value is displayed in the result

line c. Pressing the measuring button 2 again restarts a con-

tinuous measuring run.

Continuous measurement automatically switches off after

5 min. The last measured value remains indicated in the result

line c.

Indirect Distance Measurement

The indirect distance measurement is used to measure dis-

tances that cannot be measured directly because an obstacle

would obstruct the laser beam or no target surface is available

as a reflector. This measuring procedure can only be used in

vertical direction. Any deviation in horizontal direction leads

to measuring errors.

The laser beam remains switched on between the individual

measurements.

For indirect length measurements, three measuring modes

are available. Each measuring mode can be used for deter-

mining different distances.

a) Indirect height measurement (see figure C)

Press the function-mode button 4 until the indication for indi-

rect height measurement appears on the display.

Pay attention that the measuring tool is positioned at the

same height as the bottom measuring point. Now, tilt the

Unit of measure, distance

(depending on country

version)

m, ft, inch, ...

Unit of measure, angle °, %, mm/m

inch, ft

Basic Settings

OBJ_BUCH-1347-006.book Page 23 Friday, April 25, 2014 3:28 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GLM 80 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GLM 80 Manual

Product: