383796

Bosch gks 190 Manual

26
Zoom out
Zoom in
Previous page
1/319
Next page
26 | English
1 619 P06 540 | (30.9.08) Bosch Power Tools
– Adjust the desired cutting depth and the bev-
el angle. Observe the marks on the guide-rail
adapter 27 for preadjustment of the various
bevel angles; see figure F.
– Align the circular saw with guide-rail adapter
in such a manner that the teeth of the saw
blade 19 face against the rubber lip. The po-
sition of the saw blade 19 depends on the se-
lected cutting angle. Do not saw into the
guide rail.
– Tighten wing bolt 7 to lock the position of the
guide-rail adapter.
– Remove the circular saw with the premount-
ed guide-rail adapter 27 from the guide rail
28.
– Align the guide rail 28 on the workpiece in
such a manner that the rubber lip lies exactly
alongside the cutting edge.
– The guide rail 28 must not extend beyond
the face side of the workpiece where the
cut is to be started.
– Fasten the guide rail 28 with suitable clamp-
ing devices, e. g., screw clamps, on the work-
piece. Set the circular saw with the pre-
mounted guide-rail adapter 27 on to the
guide rail.
– Switch the machine on and guide it in the
cutting direction applying moderate and
steady feed.
Two guide rails can be connected to one with
use of the connection piece 29. Clamping is car-
ried out with the four screws located in the con-
nection piece.
Maintenance and Service
Maintenance and Cleaning
f Before any work on the machine itself, pull
the mains plug.
f For safe and proper working, always keep
the machine and ventilation slots clean.
The retracting blade guard must always be able
to move freely and retract automatically. There-
fore, always keep the area around the retracting
blade guard clean. Remove dust and chips by
blowing out with compressed air or with a
brush.
Saw blades that are not coated can be protect-
ed against corrosion with a thin coat of acid-free
oil. Before use, the oil must be removed again,
otherwise the wood will become soiled.
Resin and glue residue on the saw blade produc-
es poor cuts. Therefore, clean the saw blade im-
mediately after use.
If the machine should fail despite the care taken
in manufacturing and testing procedures, repair
should be carried out by an after-sales service
centre for Bosch power tools.
In all correspondence and spare parts order,
please always include the 10-digit article
number given on the type plate of the machine.
WARNING! Important instructions for con-
necting a new 3-pin plug to the 2-wire cable.
The wires in the cable are coloured according to
the following code:
Do not connect the blue or brown wire to the
earth terminal of the plug.
Important: If for any reason the moulded plug is
removed from the cable of this power tool, it
must be disposed of safely.
0° 1
-
45°
OBJ_BUCH-813-001.book Page 26 Tuesday, September 30, 2008 1:13 PM
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch gks 190 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch gks 190 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 10,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info