Manual Bosch gks 190 (page 25 of 319) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

383796

Zoom out

Zoom in

1/319

English | 25

Bosch Power Tools 1 619 P06 540 | (30.9.08)

Starting Operation

f Observe correct mains voltage! The voltage

of the power source must agree with the

voltage specified on the nameplate of the

machine. Power tools marked with 230 V

can also be operated with 220 V.

Switching On and Off

To start the machine, first push the lock-off but-

ton for the On/Off switch 2 and then press the

On/Off switch 1 and keep it pressed.

To switch off the machine, release the On/Off

switch 1.

Note: For safety reasons, the On/Off switch 1

cannot be locked; it must remain pressed during

the entire operation.

Working Advice

Protect saw blades against impact and shock.

Guide the machine evenly and with light feed in

the cutting direction. Excessive feed significant-

ly reduces the service life of the saw blade and

can cause damage to the power tool.

Sawing performance and cutting quality depend

essentially on the condition and the tooth form

of the saw blade. Therefore, use only sharp saw

blades that are suited for the material to be

worked.

Sawing Wood

The correct selection of the saw blade depends

on the type and quality of the wood and whether

lengthway or crossway cuts are required.

When cutting spruce lengthways, long spiral

chips are formed.

Beech and oak dusts are especially detrimental

to health. Therefore, work only with dust extrac-

tion.

Sawing with Parallel Guide (see figure D)

The parallel guide 10 enables exact cuts along a

workpiece edge and cutting strips of the same

dimension.

Loosen wing bolt 7 and slide the scale of the

parallel guide 10 through the guide in the base

plate 12. Adjust the desired cutting width as the

scale setting at the respective cutting mark 9 or

8; see Section “Cutting Marks”. Tighten wing

bolt 7 again.

Sawing with Auxiliary Guide (see figure E)

For sawing large workpieces or straight edges, a

board or strip can clamped to the workpiece as

an auxiliary guide; the base plate of the circular

saw can be guided alongside the auxiliary guide.

Sawing with Guide Rail (see figure F–G)

The guide rail 28 is used to carry out straight

cuts.

The adhesive coating prevents the guide rail

from slipping and protects the surface of the

workpiece. The coating of the guide rail allows

the circular saw to glide easily.

The rubber lip on the guide rail acts as a splinter

guard that prevents fraying or tearing out of the

surface when sawing wooden materials. For

this, the teeth of the saw blade must face direct-

ly against the rubber lip.

The guide-rail adapter 27 is required for working

with the guide rail 28. The guide-rail adapter 27

is mounted in the same manner as the parallel

guide 10.

The following work steps are required for exact

cuts using the guide rail 28:

– Place the guide rail 28 on to the workpiece

projecting lightly over the side. Pay attention

that the side with the rubber lip faces to the

workpiece.

– Set the circular saw with the premounted

guide-rail adapter 27 on to the guide rail 28.

OBJ_BUCH-813-001.book Page 25 Tuesday, September 30, 2008 1:13 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch gks 190 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 10,85 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch gks 190 Manual

Product: