Manual Bosch gks 190 (page 24 of 319) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

383796

Zoom out

Zoom in

1/319

24 | English

1 619 P06 540 | (30.9.08) Bosch Power Tools

Mounting the Extraction Adapter

(see figure B)

Attach the extraction adapter 22 onto the saw-

dust ejector 14 until it latches. A vacuum hose

with a diameter of 35 mm can be connected to

the extraction adapter 22.

f The extraction adapter may not be mounted

when no external dust extraction is con-

nected. Otherwise the extraction channel

can become clogged.

f Do not connect a dust bag to the extraction

adapter. Otherwise the extraction system

can become clogged.

To ensure optimum extraction, the extraction

adapter 22 must be cleaned regularly.

External Dust Extraction

Connect the vacuum hose 30 to a vacuum clean-

er (accessory). An overview for connecting to

various vacuum cleaners can be found at the

end of this manual.

The machine can be plugged directly into the re-

ceptacle of a Bosch all-purpose vacuum cleaner

with remote starting control. The vacuum clean-

er starts automatically when the machine is

switched on.

The vacuum cleaner must be suitable for the ma-

terial being worked.

When vacuuming dry dust that is especially det-

rimental to health or carcinogenic, use a special

vacuum cleaner.

Operation

Operating Modes

f Before any work on the machine itself, pull

the mains plug.

Adjusting the Cutting Depth (see figure C)

f Adjust the cutting depth to the thickness of

the workpiece. Less than a full tooth of the

blade teeth should be visible below the work-

piece.

Loosen the clamping lever 23. For a smaller cut-

ting depth, pull the saw away from the base

plate 12; for a larger cutting depth, push the

saw toward the base plate 12. Adjust the de-

sired cutting depth at the cutting-depth scale.

Tighten the clamping lever 23 again.

If the cutting depth cannot be fully adjusted af-

ter loosening clamping lever 23, pull clamping

lever 23 away from the saw and swivel it down-

ward. Release the clamping lever 23 again. Re-

peat this procedure until the requested cutting

depth can be adjusted.

If the cutting depth cannot be sufficiently locked

after tightening clamping lever 23, pull clamping

lever 23 away from the saw and swivel it up-

ward. Release the clamping lever 23 again. Re-

peat this procedure until the cutting depth is

locked.

Adjusting the Cutting Angle

Loosen the wing bolts 6 and 25. Tilt the saw

sidewards. Adjust the desired measure on the

scale 5. Tighten the wing bolts 6 and 25 again.

Note: For bevel cuts, the cutting depth is small-

er than the setting indicated on the cutting-

depth scale 24.

Cutting Marks

The 0° cutting mark (9) indicates the position of

the saw blade for right-angled cuts. The 45° cut-

ting mark (8) indicates the position of the saw

blade for 45° cuts.

For precise cuts, position the circular saw

against the workpiece as shown in the figure. It

is best to carry out a trial cut.

0 45

OBJ_BUCH-813-001.book Page 24 Tuesday, September 30, 2008 1:13 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch gks 190 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 10,85 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch gks 190 Manual

Product: