786250

Bosch GGS 18V-10 SLC Manual

18
Zoom out
Zoom in
Previous page
1/305
Next page
18 | English
Inserting the Bluetooth® Low Energy
ModuleGCY30-4
Note: The Bluetooth ® Low Energy ModuleGCY30-4 is avail-
able as an accessory.
Read the corresponding operating instructions for informa-
tion about the Bluetooth® Low Energy ModuleGCY30-4.
Battery Charging
uUse only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
uDo not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
Removing the Battery
The battery (7) is equipped with two locking levels to pre-
vent the battery from falling out when pushing the battery re-
lease button (6) unintentionally. As long as the battery is in-
serted in the power tool, it is held in position by means of a
spring.
To remove the battery(7), press the release button(6) and
pull the battery out of the power tool. Do not use force to
do this.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or to
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Note: The state of charge of the battery is also displayed on
the user interface (13) (see "Status indications", page20).
Battery model GBA 18V...
LEDs Capacity
3× continuous green light 60−100%
LEDs Capacity
2× continuous green light 30−60%
1× continuous green light 5−30%
1× flashing green light 0−5%
Battery model ProCORE18V...
LEDs Capacity
5× continuous green light 80−100%
4× continuous green light 60−80%
3× continuous green light 40−60%
2× continuous green light 20−40%
1× continuous green light 5−20%
1× flashing green light 0−5%
Fitting the Abrasive Tools (see figure A)
uRemove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
uOnly use open-ended spanners that are suitable and
undamaged (see "Technical Data").
– Clean the grinding spindle (3) and all the parts to be fit-
ted.
– Use an open-ended spanner (10) on the spanner flat of
the grinder spindle (3) to hold it in place.
Loosen the clamping nut (2) by placing an open-ended
spanner (11) on the spanner flat and turning it counter-
clockwise.
– Insert the straight shank of the grinding tool all the way
into the collet (1).
– Hold the grinding spindle (3) with the open-ended span-
ner (10) and tighten the application tool by placing the
open-ended spanner (11) on the spanner flat and turning
it clockwise.
The grinding tools must run completely concentrically. Do
not continue to use damaged grinding tools that are out of
balance. If the grinding tools are out of balance, they should
be replaced.
uDo not, under any circumstances, tighten the collet
with the clamping nut until a grinding tool has been
fitted. The collet may otherwise become damaged.
uOnly use mounted points with an appropriate shank
diameter. A mounting point with a shank diameter which
does not correspond to the tool holder of the power tool
(see "Technical data") cannot be held properly and will
damage the collet chuck.
uThe application tool must be clamped at least 10 mm.
The inner shank dimension L0 can be used to calculate the
maximum permitted speed of the application tool from
1 609 92A 6DP | (15.06.2021) Bosch Power Tools
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GGS 18V-10 SLC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GGS 18V-10 SLC in the language / languages: All languages as an attachment in your email.

The manual is 4.83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info