388800

Bosch gbh 24 0 vre Manual

24
Zoom out
Zoom in
Previous page
1/282
Next page
24 | English
1 619 929 740 | (24.7.07) Bosch Power Tools
Reversing the Rotational Direction
f Actuate the rotational direction switch 7
only when the machine is at a standstill.
The rotational direction switch 7 is used to re-
verse the rotational direction of the machine.
However, this is not possible with the On/Off
switch 8 actuated.
Right Rotation: For drilling and driving in
screws, push the rotational direction switch 7
left to the stop.
Left Rotation: For loosening and unscrewing
screws and nuts, press the rotational direction
switch 7 through to the right stop.
Switching On and Off
To start the machine, press the On/Off switch 8
and keep it depressed.
To switch off the machine, release the On/Off
switch 8.
For low temperatures, the machine reaches the
full hammer/impact capacity only after a certain
time.
This start-up time can be shortened by striking
the inserted tool insert against the floor one
time.
Setting the Speed/Impact Rate
The speed/impact rate of the switched on pow-
er tool can be variably adjusted, depending on
how far the On/Off switch 8 is pressed.
Light pressure on the On/Off switch 8 results in
low speed/impact rate. Further pressure on the
switch increases the speed/impact rate.
Run-on Brake
When the On/Off switch 8 is released, the chuck
brakes to a stop, thus preventing the run-on of
the tool.
When driving in screws, wait until the screw is
screwed in flush with the material and then re-
lease the On/Off switch 8. By doing so, the head
of the screw does not penetrate into the materi-
al.
Overload Clutch
f If the tool insert becomes caught or
jammed, the drive to the drill spindle is in-
terrupted. Because of the forces that occur,
always hold the power tool firmly with both
hands and provide for a secure stance.
f If the power tool jams, switch the machine
off and loosen the tool insert. When switch-
ing the machine on with the drilling tool
jammed, high reaction torques can occur.
Operating Instructions
f Do not operate the power tool stationary. It
is not designed for operation in a drill stand.
Inserting Screwdriver Bits (see figure I)
f Apply the power tool to the screw/nut only
when it is switched off. Rotating tool inserts
can slip off.
To work with screwdriver bits, a universal bit
holder 22 with SDS-plus shank (accessory) is re-
quired.
Clean the shank end of the adapter shank and
apply a light coat of grease.
Insert the universal bit holder with a turning mo-
tion into the tool holder until it automatically
locks.
Check the locking effect by pulling the universal
bit holder.
Insert a screwdriver bit into the universal bit
holder. Use only screwdriver bits that match the
screw head.
Set the selector switch 6 to the “Drilling” sym-
bol.
To remove the universal bit holder, pull the lock-
ing sleeve 3 toward the rear and remove the uni-
versal bit holder 22 out of the tool holder.
OBJ_BUCH-372-001.book Page 24 Tuesday, July 24, 2007 1:31 PM
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch gbh 24 0 vre at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch gbh 24 0 vre in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info