458024
49
Zoom out
Zoom in
Previous page
1/76
Next page
6 720 645 349 (2010/09)
Menu settings INSTALLER SETTINGS (contractors only) | 49
Menu: Heating parameters > Foot point
B Set the base point of the heating curve
according to the classic base point/end point
method.
Menu: Heating parameters > End point
B Set the end point of the heating curve in line
with the classic base point/end point method.
Menu: Heating parameters > Design flow temp.
B Set the design flow temperature to suit the
type of heating system:
For Underfloor heating e.g. 45 °C set flow
temperature.
For Radiators e.g. 75 °C set flow
temperature.
For Convectors e.g. 80 °C set flow
temperature.
Menu: Heating parameters > Maximum CH flow
temperature
B Set the maximum flow temperature to suit the
type of heating system:
For Underfloor heating e.g. 55 °C
maximum set flow temperature.
For Radiators e.g. 80 °C maximum set flow
temperature.
For Convectors e.g. 80 °C maximum set
flow temperature.
Menu: Heating parameters > Room influence
Room influence only appears if the controller is
wall mounted.
B Set the room temperature influence on the
heating curve:
0 %: No room temperature influence
100 %: Maximum room temperature
influence
Menu: Heating parameters > Room influence
enabled for levels
B Select the operating modes during which
room temperature influence should be active:
Eco/Frost: Room temperature influence is
only active in these operating modes.
Comfort/Eco/Frost: Room temperature
influence is always active.
Menu: Heating parameters > Sensor(s) used for
room influence
Sensor(s) used for room influence only appears
if a remote control FB 10 is connected.
B Select Sensor(s) used for room influence:
Lower temperature: Of the temperature
sensors fitted in FW 100 and in FB 10, the
one with the lower captured temperature
is used.
Internal sensor: The temperature sensor
fitted inside the controller FW 100 is used.
Default setting of parameters for
heating curve
Foot point/End point Underfloor heating Radiators Convectors
Heating surface exponent (fixed
value), curvature of heating curve
1.1 1.3 1.4
Minimum outside temperature – 15 °C – 15 °C – 15 °C
Foot point 25 °C – –
End point 75 °C – –
Design flow temp. 45 °C 75 °C 80 °C
Maximum CH flow temperature 80 °C 55 °C 80 °C 80 °C
Room temperature offset 0.0K 0.0K 0.0K 0.0K
Heating off at outside temperature 20 °C 20 °C 20 °C 20 °C
Tab. 8
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch FW 100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch FW 100 in the language / languages: English as an attachment in your email.

The manual is 4,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch FW 100

Bosch FW 100 User Manual - English - 40 pages

Bosch FW 100 Usermanual and installation guide - German - 76 pages

Bosch FW 100 Quick start guide - German - 2 pages

Bosch FW 100 Quick start guide - Dutch - 2 pages

Bosch FW 100 User Manual - Dutch - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info