Manual Bosch AKE 40-19S (page 24 of 153) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

105962

Zoom out

Zoom in

1/153

English - 24

24 • F016 L70 506 • TMS • 19.10.07

The chain saw operator should keep on the uphill

side of the terrain as the tree is likely to roll or slide

downhill after it is felled.

➋ An escape path should be planned and cleared

as necessary before cuts are started. The escape

path should extend back and diagonally to the rear

of the expected line of fall.

➌ Before felling is started, consider the natural lean

of the tree, the location of larger branches and the

wind direction to judge which way the tree will fall.

Remove dirt, stones, loose bark, nails staples, and

wire from the tree.

Notching Undercut: Make the notch (X – W) 1/

3 the diameter of the tree, perpendicular to the direc-

tion of falls as Make the lower horizontal notching cut

first. This will help to avoid pinching either the saw

chain or the guide bar when the second notch is be-

ing made.

Felling Back Cut: Make the felling back cut (Y) at

least 50 mm higher than the horizontal notching cut.

Keep the felling back cut parallel to the horizontal

notching cut. Make the felling back cut so enough

wood is left to act as a hinge. The hinge wood keeps

the tree from twisting and falling in the wrong direc-

tion. Do not cut through the hinge.

As the felling gets close to the hinge the tree should

begin to fall. If there is any chance that the tree may

not fall in desired direction or it may rock back and

bind the saw chain, stop cutting before the felling

back cut is complete and use wedges of wood, plas-

tic or aluminium to open the cut and drop the tree

along the desired line of fall.

When the tree begins to fall remove the chain saw

from the cut, stop the motor, put the chain saw down,

then use the retreat path planned. Be alert for over-

head limbs falling and watch your footing.

To complete the felling operation, drive a wedge (Z)

into the horizontal cut.

Beware of falling branches when the tree starts to

move.

Limbing a Tree

Limbing is removing the branches from a fallen

tree. When limbing leave larger lower limbs to sup-

port the log off the ground. Remove the small limbs

in one cut as illustrated. Branches under tension

should be cut from the bottom up to avoid binding

the chain saw.

Bucking a Log

Bucking is cutting a log into lengths. It is impor-

tant to make sure your footing is firm and your weight

is evenly distributed on both feet. When possible, the

log should be raised and supported by the use of

limbs, logs or chocks. Follow the simple directions

for easy cutting.

When the log is supported along its entire length as

illustrated, it is cut from the top (overbuck).

When the log is supported on one end, as illus-

trated, cut 1/3 the diameter from the underside (un-

derbuck). Then make the finished cut by overbuck-

ing to meet the first cut.

When the log is supported on both ends, as illus-

trated, cut 1/3 the diameter from the top overbuck.

Then make the finished cut by underbucking the

lower 2/3 to meet the first cut.

When bucking on a slope always stand on the

uphill side of the log, as illustrated. When "cutting

through”, to maintain complete control release the

cutting pressure near the end of the cut without re-

laxing your grip on the chain saw handles. Don’t let

the chain contact the ground. After completing the

cut, wait for the saw chain to stop before you move

the chain saw. Always stop the motor before moving

from tree to tree.

Before any work on the machine itself, pull

the mains plug from the socket.

Note: To ensure long and reliable service, carry out

the following maintenance regularly.

Regularly check for obvious defects such as loose,

dislodged or damaged chain and chain bar, loose

fixings and worn or damaged components.

Care has to be taken that the chain is loosened with

the chain tensioning ring 13 before disassembly of

the chain. Forgetting to loosen can damage the

SDS mechanism.

Check that covers and guards are undamaged and

correctly fitted. Carry out necessary maintenance or

repairs before using the chain saw.

If the chain saw should happen to fail despite the

care taken in manufacturing and testing, repair

should be carried out by an authorized customer

service agent.

Before returning, ensure all oil in the oil tank has

been emptied by removing the sieve during emp-

tying. Replace sieve.

For all correspondence and spare parts orders, al-

ways include the 10-digit part number (TYP) from

the nameplate of the machine!

Fit the chain and chain bar as described in “Assem-

bly and Tensioning Chain”.

The circular groove of the chain bar will wear partic-

ularly on the lower edge with time. When replacing

the chain turn the chain bar 180° to allow even wear,

thus extending chain bar life.

Maintenance

Replacing/Changing Chain

and Chain Bar

F016 L70 506 - GB Seite 24 Dienstag, 23. Oktober 2007 3:20 15

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AKE 40-19S in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 11,91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch AKE 40-19S

Bosch AKE 40-19S User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 153 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch AKE 40-19S Manual

Product: