Manual Bosch AKE 40-19S (page 22 of 153) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

105962

Zoom out

Zoom in

1/153

English - 22

22 • F016 L70 506 • TMS • 19.10.07

Important: The chain saw is not supplied

filled with oil. It is essential to fill with oil

before use. Never operate the chain saw

without chain oil or at an empty oil tank level, as

this will result in extensive damage to the prod-

uct.

Chain life and cutting capacity depend on optimum

lubrication. Therefore, the chain is automatically

oiled during operation via the oil outlet 19.

Filling oil tank:

– Set chain saw on any suitable surface with oil filler

cap 4 facing upward.

– Clean area around the oil filler cap 4 with cloth,

unscrew cap.

– Do not remove filter insert during filling.

– Add Bosch biodegradable chain saw oil until res-

ervoir is full.

– Avoid dirt or debris entering oil tank, refit oil filler

cap 4 and tighten.

Important: To allow venting of the oil res-

ervoir,small breather channels are pro-

vided between the oil filler cap and the

strainer, to prevent leakage ensure machine is

left in a horizontal position (oil filler cap 4 upper-

most) when not in use.

It is important to use only the recommended bi-

odegradable oil to avoid damage to the chain

saw. Never use recycled/old oil. Use of non ap-

proved oil will invalidate the warranty.

Observe the correct mains voltage! The voltage

of the power source must agree with the value given

on the nameplate of the machine. Machines desig-

nated for 230 V can also be operated with 220 V.

Switching On and Off

Hold chain saw as described in “Cutting”.

For switching on the machine, press the lock-off

button 3, then fully press the On/Off switch 2 and

hold in this position. The lock-off button 3 can now

be released.

For switching off, release the On/Off switch 2.

Do not stop chain saw after sawing by activating

the front hand guard (kickback brake).

The chain saw is equipped with two chain brake sys-

tems for user safety:

The run down brake automatically stops the chain

and motor after the switch lever (On/Off) 2 is re-

leased.

The kickback brake is a safety mechanism acti-

vated through the front hand guard 5, when kickback

occurs. Chain stops immediately.

The following function check should be carried out at

regular intervals. Push front hand guard 5 forward

(position ➋) that the red marker 28 under indicator 6

is visible and start the chain saw. The chain must not

start. To deactivate the kickback brake, pull hand

guard 5 backwards (position ➊) that the red

marker 28 under the indicator 6 is covered (see fig-

ure ).

Before Cutting

Before and periodically during cutting check as fol-

lows:

– Is the chain saw in a fail-safe condition?

– Is the oil reservoir filled? Check oil level

gauge 26 prior to starting and regularly during op-

eration. Refill oil when oil level is low. The oil tank

filling will last approx. 15 minutes, depending on

sawing intensity and stops.

– Is the chain tension in order and is the chain

sharp? Check chain tension every 10 minutes

during operation. Upon initial operation, new

chains can lengthen considerably. The condition

of the chain influences the the cutting perform-

ance. Only a sharp chain protects from overload.

– Is the kickback brake deactivated and its function

ensured?

– Are you wearing the necessary protective equip-

ment? Wear safety glasses and hearing protec-

tion. Further protective equipment for head, hand,

legs and feet is recommend. Adequate protective

clothing will reduce personal injury by flying de-

bris or accidental contact with saw chain.

Kickback

Kickback is the sudden backward/upward motion of

the chain saw, occuring when the chain (at the tip of

the chain bar) comes in contact with a log or wood,

or when the chain becomes jammed.

When kickback occurs the chainsaw reacts unpred-

icably and can cause severe injuries to the operator

or bystanders.

Lubrication

Starting and Stopping

A B

Kickback Brake/

Run Down Brake

Cutting

F016 L70 506 - GB Seite 22 Dienstag, 23. Oktober 2007 3:20 15

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AKE 40-19S in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 11,91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch AKE 40-19S

Bosch AKE 40-19S User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 153 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch AKE 40-19S Manual

Product: