Manual Bosch AKE 35 (page 21 of 135) (Dutch)

1151

Zoom out

Zoom in

1/135

English - 6

21 • F016 L70 362 • TMS • 24.01.06

– Always use a Bosch low-kickback chain.

– Apply the metal gripping teeth 11 for leverage.

– Ensure correct chain tension.

General Behavior

Always hold the chain saw firmly with both

hands. Front grip with the left hand and rear grip with

the right hand. Fully grip both handles at all times

during operation. Never operate chain saw using

only one hand. Ensure power cord is located to the

rear, away from the chain and wood and so pos-

tioned that it will not be caught on branches or the

like during cutting.

Use the chain saw only with secure footing. Hold

the chain saw at the right-hand side of your body.

The chain must be running at full speed before it

makes contact with the wood. Use the metal grip-

ping teeth 11 to secure the saw onto the wood be-

fore starting to cut. Use the gripping teeth as a lev-

erage point “X” while cutting.

Reset the gripping teeth at a lower point when saw-

ing thicker logs by pulling the chain saw slightly

backwards until the gripping teeth release, and repo-

sition at lower level to continue sawing. Do not re-

move the saw completely from the wood.

Do not force the chain while cutting, let the chain do

the work, using the gripping teeth 11 to apply mini-

mal leverage pressure.

Do not operate the chain saw with arms fully ex-

tended or attempt to saw areas which are difficult to

reach, or on a ladder. Never use the chain saw

above shoulder height.

Sawing is optimized when the chain speed remains

steady during cutting.

Beware when reaching the end of the cut. The

weight of the saw may change unexpectedly as it

cuts free from the wood. Accidents can occur to the

legs and feet.

Always remove the saw from a wood cut while the

saw is running.

Cutting Logs

Observe the following safety instructions:

Support logs so that the face sides at the cut

do not close in against each other, which would re-

sult in the chain being jammed or pinched.

Position and set short logs safely prior to sawing.

Saw only wood or wooden objects. When sawing, al-

ways take care to avoid hitting stones, nails, etc., as

these could be thrown up or cause damage to the

chain or serious injury to the operator or bystanders.

Keep a running saw clear of wire fencing or the

ground.

Use of the saw to thin out branches or bushes is not

approved.

Length cuts must be carried out with care, as lever-

age with the gripping teeth 11 is not possible. Saw at

a flat angle to avoid kickback.

When working on a slope, operate above or to the

side of the trunk or laying tree.

Be careful not to trip over tree stumps, branches,

roots, etc.

Cutting Wood under Tension

There is a high risk of accidents when sawing wood,

branch or trees under tension. Be extremely careful.

Leave saw jobs like these to professionals.

When sawing logs supported on both ends, start the

cut from above (Y) about 1/3 of the diameter into the

log and then finish the cut (Z) from below, in order to

avoid splitting of the log or jamming of the saw.

Avoid contact of the chain saw with the ground.

When sawing logs supported on only one end, start

the cut from below (Y) about 1/3 of the diameter into

the log and finish the cut from above (Z), in order to

avoid log splitting or jamming of the chain saw.

Felling Trees

Always wear hard hat to protect head

against falling branches.

The chain saw can only be used to fell trees

smaller in diameter than the length of the chain

bar.

➊ Secure work area. Ensure no persons or ani-

mals are in the vicinity of the falling tree.

Never attempt to free a jammed saw with the mo-

tor running. Use wooden wedges to free chain

and chain bar.

When cutting and felling operations are being per-

formed by two or more persons, at the same time,

the felling operations should be separated from the

cutting operation by a distance of at least twice the

height of the tree being felled. Trees should not be

felled in a manner that would endanger any person,

strike any utility line or cause any property damage.

If the tree does make contact with any utility line, the

company should be notified immediately.

The chain saw operator should keep on the uphill

side of the terrain as the tree is likely to roll or slide

downhill after it is felled.

➋ An escape path should be planned and cleared

as necessary before cuts are started. The escape

path should extend back and diagonally to the rear

of the expected line of fall.

➌ Before felling is started, consider the natural lean

of the tree, the location of larger branches and the

wind direction to judge which way the tree will fall.

Remove dirt, stones, loose bark, nails staples, and

wire from the tree.

Notching Undercut: Make the notch (X – W) 1/

3 the diameter of the tree, perpendicular to the direc-

tion of falls as Make the lower horizontal notching cut

first. This will help to avoid pinching either the saw

chain or the guide bar when the second notch is be-

ing made.

E H

F016 L70 362 - GB Seite 6 Mittwoch, 25. Januar 2006 8:47 08

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AKE 35 in the language / languages: Dutch as an attachment in your email.

The manual is 3,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch AKE 35

Bosch AKE 35 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 139 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch AKE 35 Manual

Product: