1151
20
Zoom out
Zoom in
Previous page
1/135
Next page
English - 5
20 • F016 L70 362 • TMS • 24.01.06
Important: The chain saw is not supplied
filled with oil. It is essential to fill with oil
before use. Never operate the chain saw
without chain oil or at an empty oil tank level, as
this will result in extensive damage to the prod-
uct.
Chain life and cutting capacity depend on optimum
lubrication. Therefore, the chain is automatically
oiled during operation via the oil outlet 19.
Filling oil tank:
Set chain saw on any suitable surface with oil filler
cap 4 facing upward.
Clean area around the oil filler cap 4 with cloth,
unscrew cap.
Add Bosch biodegradable chain saw oil until res-
ervoir is full.
Avoid dirt or debris entering oil tank, refit oil filler
cap 4 and tighten.
Important: To allow venting of the oil res-
ervoir,small breather channels are pro-
vided between the oil filler cap, to prevent
leakage ensure machine is left in a horizontal po-
sition (oil filler cap 4 uppermost) when not in
use.
It is important to use only the recommended bi-
odegradable oil to avoid damage to the chain
saw. Never use recycled/old oil. Use of non ap-
proved oil will invalidate the warranty.
Observe the correct mains voltage! The voltage
of the power source must agree with the value given
on the nameplate of the machine. Machines desig-
nated for 230 V can also be operated with 220 V.
Starting
Hold chain saw as described in “Cutting”.
Press the lock-off button 3, then fully press the On/
Off switch 2 and hold in this position. The lock-off
button 3 can now be released.
Stopping
Release the On/Off switch 2.
Do not stop chain saw after sawing by activating
the front hand guard (kickback brake).
The kickback brake is a safety mechanism acti-
vated through the front hand guard 5, when kickback
occurs. Chain stops immediately.
The following function check should be carried out at
regular intervals. Push front hand guard 5 forward
(position ) and start the chain saw. The chain must
not start. To deactivate the kickback brake, release
On/Off switch 2 and pull hand guard 5 backwards
(position ).
Before Cutting
Before and periodically during cutting check as fol-
lows:
Is the chain saw in a fail-safe condition?
Is the oil reservoir filled? Check oil level
gauge 26 prior to starting and regularly during op-
eration. Refill oil when oil level is low. The oil tank
filling will last approx. 15 minutes, depending on
sawing intensity and stops.
Is the chain tension in order and is the chain
sharp? Check chain tension every 10 minutes
during operation. Upon initial operation, new
chains can lengthen considerably. The condition
of the chain influences the the cutting perform-
ance. Only a sharp chain protects from overload.
Is the kickback brake deactivated and its function
ensured?
Are you wearing the necessary protective equip-
ment? Wear safety glasses and hearing protec-
tion. Further protective equipment for head, hand,
legs and feet is recommend. Adequate protective
clothing will reduce personal injury by flying de-
bris or accidental contact with saw chain.
Kickback
Kickback is the sudden backward/upward motion of
the chain saw, occuring when the chain (at the tip of
the chain bar) comes in contact with a log or wood,
or when the chain becomes jammed.
When kickback occurs the chainsaw reacts unpred-
icably and can cause severe injuries to the operator
or bystanders.
Particular attention must be given when sawing
sidewards, slanted or during length cuts, as the grip-
ping teeth 11 usually can not be applied.
To avoid kickback:
Saw with the chain bar at a flat angle.
Never work with a loose, widely stretched or the
heavily worn out chain.
Ensure chain is sharpened correctly.
Never saw above shoulder height.
Never work with the tip of the chain bar.
Always the hold chain saw firmly with both hands.
Lubrication
Starting and Stopping
A B
Kickback Brake
Cutting
D
B
D
F016 L70 362 - GB Seite 5 Mittwoch, 25. Januar 2006 8:47 08
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch AKE 35 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AKE 35 in the language / languages: Dutch as an attachment in your email.

The manual is 3,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch AKE 35

Bosch AKE 35 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 139 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info