Manual Bosch AdvancedDrill 18 (page 19 of 227) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

707735

Zoom out

Zoom in

1/227

Fitting

Battery charging

u Use only the chargers listed on the accessories page.

Only these chargers are matched to the lithium-ion bat-

tery of your power tool.

Note: The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger

before using your power tool for the first time.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the "Electronic Cell Protection (ECP)". When the battery

is discharged, the power tool is switched off by means of a

protective circuit: The application tool no longer rotates.

u Do not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

Removing the battery

To remove the battery , press the battery release button and

pull the battery to the rear and out of the power tool. Do not

use force to do this.

Battery charge indicator

When the on/off switch (14) is pressed in halfway or com-

pletely, the battery charge-control indicator (13) indicates

the charge condition of the battery for several seconds. The

indicator consists of three green LEDs.

LED Capacity

Continuous lighting 3x green ≥ 66%

Continuous lighting 2x green 33–66%

Continuous lighting 1x green 11–33%

Slowly flashing light 1 x green ≤ 10%

The three LEDs in the battery charge indicator flash

quickly when the temperature of the battery is outside

the operating temperature range of –30 to +65 °C and/or

the overload protection has been triggered.

Changing the Tool

Inserting the application tool (seefigureA)

Insert the application tool all the way into the tool holder (2).

The application tool is held in the tool holder by means of a

magnet.

Removing

Remove the application tool from the tool holder (2).

Fitting the adapter (see figure B)

Remove the application tool.

Insert the adapter into the tool holder (2). The adapter clicks

audibly into place.

Check that it is seated securely by pulling the adapter.

Inserting the application tool into the adapter (see figure

Insert the application tool all the way into the adapter. The

application tool is held in the adapter by means of a magnet.

Screw holder (see figure D)

The screw holder (16) stabilises the screws so that they can

be better positioned on the workpiece.

Remove the application tool.

Push the screw holder onto the tool holder (2) until it aud-

ibly engages. Push the magnetic cap (15) as far as it will go

towards the power tool.

Then push the screwdriver bit (20) onto the screw holder

(16) and pull the magnetic cap forwards over the screw-

driver bit.

Push a screw onto the screwdriver bit.

Drill chuck adapter (see figure E)

Open the drill chuck adapter (18) by turning it in the direc-

tion of rotation  until the application tool can be inserted.

Insert the application tool.

Firmly tighten the sleeve of the drill chuck adapter (18) by

turning it by hand in the direction of rotation . This will

automatically lock the drill chuck.

Turning the adapter (see figure F)

Pull the unlocking ring (1) away from the power tool and

then pull the adapter off the tool holder (2).

Turn the adapter to the required position and then reattach

it.

Check that it is seated securely by pulling the adapter.

Removing the adapter (see figure G)

Remove the application tool.

Pull the unlocking ring (1) away from the power tool and

then pull the adapter off the tool holder (2).

Combining adapters (see figure H)

Remove the application tool.

Push the angle screw adapter (17) onto the tool holder (2).

Check that it is seated securely by pulling the angle screw

adapter (17).

Push the drill chuck adapter (18) onto the angle screw ad-

apter (17).

Check that it is seated securely by pulling the drill chuck ad-

apter (18).

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some

wood types, minerals and metal can be harmful to one’s

English | 19

Bosch Power Tools 1 609 92A 4BE | (07.09.2018)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AdvancedDrill 18 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 18,34 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch AdvancedDrill 18 Manual

Product: