Manual Bosch AdvancedDrill 18 (page 20 of 227) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

707735

Zoom out

Zoom in

1/227

20 | English

1 609 92A 4BE | (07.09.2018) Bosch Power Tools

health. Touching or breathing-in the dust can cause allergic

reactions and/or lead to respiratory infections of the user or

bystanders.

Certain dust, such as oak or beech dust, is considered carci-

nogenic, especially in connection with wood-treatment ad-

ditives (chromate, wood preservative). Materials containing

asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the ma-

terials to be worked.

u Avoid dust accumulation at the workplace. Dust can

easily ignite.

Operation

Starting Operation

Inserting the battery

Push the charged battery (9) into the base of the power tool

from the rear until the battery is securely locked.

Setting the rotational direction

The electronic rotational direction switch (7) is used to

change the rotational direction of the power tool. However,

this is not possible while the on/off switch (14) is being

pressed.

Setting right rotation (see figure I)

To drill and drive in screws, push the electronic rotational

direction switch (7) down.

The rotational direction indicator for right rotation

(5) lights up when the on/off switch (14) is

pressed, the rotational direction switch (7) is

pressed and the motor is running.

Setting left rotation (see figure J)

To loosen or undo screws and nuts, push the electronic rota-

tional direction switch (7) down.

The rotational direction indicator for left rotation

(6) lights up when the on/off switch (14) is

pressed, the rotational direction switch (7) is

pressed and the motor is running.

Preselecting the torque

The torque presetting ring (3) can be used to preselect the

required torque in 20 stages and "MAX". Once the set torque

has been reached, the application tool will be stopped.

Setting the operating mode (see figure K)

u Only operate the mode selector switch (4) when the

power tool is not in use.

You can pre-select two speed ranges with the mode selector

switch (4).

Screwdriving mode (first screw phase):

Low speed range; for screwdriving or working with a large

drilling diameter.

Drilling/impact drilling mode (second screw phase):

High speed range; for working with a small drilling diameter.

Screwdriving

Set the torque presetting ring (3) to the re-

quired torque.

Set the mode selector switch (4) to the

"screwdriving" symbol.

Drilling

Set the torque presetting ring (3) to "MAX".

Set the mode selector switch (4) to the

"drilling" symbol.

Impact drilling (AdvancedImpact 18)

Set the torque presetting ring (3) to "MAX".

Set the mode selector switch (4) to the "im-

pact drilling" symbol.

Switching on/off

To start the power tool, press and hold the on/off switch

(14).

The light (12) lights up when the on/off switch (14) is lightly

or fully pressed, meaning that the work area is illuminated in

poor lighting conditions.

To switch off the power tool, release the on/off switch (14).

Adjusting the Speed

You can adjust the speed of the power tool when it is on by

pressing in the on/off switch to varying extents.

Applying light pressure to the on/off switch results in a low

rotational speed. Applying increasing pressure to the switch

increases the speed.

Fully automatic spindle lock (Auto-Lock)

The drill spindle, and therefore the tool holder, are locked

when the on/off switch (14) is not pressed.

This allows screws to be driven in even when the battery is

discharged and enables the power tool to be used as a

screwdriver.

Temperature-dependent overload protection

In normal conditions of use, the power tool cannot be over-

loaded. If the power tool is overloaded or the permitted bat-

tery temperature is exceeded, the electronics of the power

tool will switch off until the temperature returns to within the

optimum operating temperature range.

The three LEDs in the battery charge indicator (13) and the

PowerLight (12) flash quickly when the temperature of the

battery is outside the operating temperature range of –20 to

+50 °C and/or the overload protection has been triggered.

Protection against deep discharge

The lithium-ion battery is protected against deep discharge

by the Electronic Cell Protection (ECP). When the battery is

discharged, the power tool is switched off by means of a pro-

tective circuit: The application tool no longer rotates.

Working Advice

u Only apply the power tool to the screw when the tool

is switched off. Rotating application tools can slip off.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AdvancedDrill 18 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 18,34 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch AdvancedDrill 18 Manual

Product: