714396
21
Zoom out
Zoom in
Previous page
1/32
Next page
EN
21
Gas installation
www.bora.com
Set the gas pressure at the gas supply pipe (LPG
pressure bottle) to 2.75 kPa.
Ignite the burner (see the Operation chapter).
Check the burner flame.
Close the gas supply after successfully setting the
pressure.
Set the control knob to the 0 position.
Shut off the measuring device from the test point.
Securely screw the test point screw back into the test
point adapter.
Check that the screw is positioned correctly.
Subsequent installation work for both gas
types (NG/LPG)
Check the tightness of the gas connection by
conducting a leak test (see Leak test section).
Switch on the main switch/automatic circuit breaker.
Put the cooktop into operation (see the Operation
chapter).
Check all the functions and the burner flame are
working correctly.
6.3 Leak test of the gas connection
Ensure that no ignition sparks could be created.
Do not use fire or an open flame.
Use suitable testing equipment to check all the
connections on the gas connections.
When using a leak spray for this process, ensure that
you wet all connections.
Close the gas supply if you determine that gas is
escaping and ventilate the room.
Seal the point from which the gas is leaking.
Re-check all connections and the gas connection.
Repeat the leak test until all connections are tight.
Create a leak test record and give this to the user.
6.4 Changing the gas type
Set the control knob to the 0 position.
Close the gas supply to the gas supply pipe.
Switch off the main switch/automatic circuit breaker.
Protect the main switch/automatic circuit breaker
from being switched on without permission.
Make sure the device is not energised.
Natural gas (NG)
If the cooktop is connected to a natural gas (NG) supply,
a gas regulator must be installed with a test point.
The gas regulator and the transition piece are included in
the scope of delivery of the appliance.
1
Fig. 6.1 Connection with gas regulator (NG)
[1] Gas regulator
Connect the gas regulator [1] to the connection on
the gas cooktop using the transition pieces and
the suitable seal.
Note the gas flow direction of the gas regulator [1].
Liquid gas (LPG)
If the cooktop is attached to a liquid gas supply (LPG),
the supply is controlled on the gas bottle.
For this purpose, install only the test point adapter
with the transition piece in the gas supply pipe.
The test point adapter and the transition piece are
included in the scope of delivery of the appliance.
1
Fig. 6.2 Connection to the test point adapter (LPG)
[1] Test point adapter
Connect the test point adapter [1] to the connection
on the gas cooktop using the transition pieces and the
suitable seal.
Ensure that the seal is positioned correctly.
Provide the necessary transition piece on the supply
side with appropriate seals at the installation site.
Tighten all connections so that they are secure.
Check that installation has been done correctly.
Check the correct functioning of the stopcock.
Check the gas pressure (LPG) as follows:
Set the control knob to the 0 position.
Close the gas supply.
Unscrew the test point screw completely.
Connect your measuring device to the test point
connection.
Open the gas supply.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bora CG11 Classic at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bora CG11 Classic in the language / languages: English as an attachment in your email.

The manual is 2,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bora CG11 Classic

Bora CG11 Classic User Manual - German - 32 pages

Bora CG11 Classic User Manual - Dutch - 32 pages

Bora CG11 Classic User Manual - French - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info