814370
31
Zoom out
Zoom in
Previous page
1/48
Next page
31
Connection to the water supply
Connect the water inlet hose and the water drain
hose properly. Follow the instructions given under
"Water connection"
.
Installation to the power supply
Follow the instructions given under
"Electrical con-
nection"
.
Adjusting the feet
Place the appliance in its proper position and make
sure that it is firm and level. Check this with a spirit
level.
The maximum adjust-
ment height of the feet
is 50 mm.
The rear stand can be adjusted with an Allen key
via a set screw (a) in the center of the appliance
base front.
Adjust the front feet (b) with a wrench until the
dishwasher is level.
Fixing the dishwasher
Fix the appliance with the enclosed screws in the
holes provided.
A If the worktop is made of wood, fasten the appli-
ance to the worktop.
B If the worktop is made of marble or granite, fasten
the appliance to the side with the cabinet unit.
Put on the screw cover caps.
Water connection
CAUTION:
Installation to the water supply must be carried
out in accordance with local laws and regulations.
The appliance is not suitable for hot water supply.
Use the new hose set supplied to connect the
appliance to the water supply. Do not reuse old or
used connection sets.
If the water supply is new or has not been used
for a long time, make sure that the water is clear
and free of impurities before connecting it to the
water supply.
NOTE, the connection to the water mains may only
be made in accordance with DIN EN 1717 of the
drinking water ordinance. A suitable safety device
against drinking water contamination through back-
flow must be installed.
Notes on inlet hose safety system
(delivery scope depending on model)
The safety system consists of a double-walled inlet
hose. It guarantees to cut off the water supply when
leakage of the inner hose. Switching off the water
supply leads over an electronic contact.
If necessary, you can order an inlet hose safety sys-
tem from your dealer or in our online accessories
shop, www.bomann-germarny.de. To order, use the
reference number found under
“Technical data”
.
Connecting the water inlet hose
(cold water connection)
NOTE:
The water pressure must be between 0.04-1.0 MPa.
For higher water pressure: connect pressure reduc-
ing valve upstream.
Connect the water inlet hose to a
water thread with ¾“. Tighten the
hose in the direction of the screw
thread; make sure it is firmly
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann GSPE 7413 TI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann GSPE 7413 TI in the language / languages: English, German as an attachment in your email.

The manual is 2.05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info