The bread baking machine sets the baking temperature and time automatically. If the bread is too light at the
end of the baling program, use the BACKEN program to let it brown more.
To do so, press the START/STOP key, then select the BACKEN program and start. When the desired
degree of baking has been reached, stop the process.
Warming
WarmingWarming
Warming
Once the baking is over, the buzzer goes off to signal that the bread or specialty can be removed. The 1-hour
warming time starts immediately.
End of the program phases
End of the program phasesEnd of the program phases
End of the program phases
Please switch the appliance off at the end of the programme by setting the On/Off switch (L) to "0". Now
remove the baking tin using oven cloths, turn it over and as long as the bread does not immediately fall onto the
grid, move the kneading shaft back and forth a few times from below until the bread falls out. If one of the
kneading pegs is still stuck in the bread, take the hook supplied with the appliance. Insert it under the warm loaf
of bread into the almost circular opening of the kneading peg and wedge the hook against the lower edge of the
kneading peg preferably where the blade of the kneading peg is located. Then pull the kneading peg carefully
out with the hook.You can now easily cut the bread and remove completely the kneading pegs.
Heating the appliance to make the dough rise
Heating the appliance to make the dough riseHeating the appliance to make the dough rise
Heating the appliance to make the dough rise
The heating is switched on only if the room temperature is lower than 25°C. If the room temperature is above
25°C the ingredients are already at the right temperature and there is no need for pre-heating. For the first and
second rising the room temperature must be above 25°C or high enough to make the dough rise without extra
heating.
Cleaning and Maintenance
Cleaning and MaintenanceCleaning and Maintenance
Cleaning and Maintenance
•Before using the appliance for the first time wash the bread baking machine’s baking tin (never dip in water)
with water and clean the kneading pegs.
•It is highly recommended to coat the new baking tin and the kneading pegs with heat resistant grease
before using them for the first time and let them heat in the oven for about 10 minutes at 160°C. Once
these have cooled down clean away (polish) the grease from the baking tin with a sheet of paper towel.
This operation is to be performed to protect the nonstick coating. This operation can be repeated from time
to time.
•After use always leave the appliance to cool before cleaning it or putting it away. It takes about half an hour
for the appliance to cool and to be ready again for baking and kneading.
•Before cleaning pull out the plug and leave the appliance to cool. Never use chemical cleaning agents,
gasoline, oven cleaners or any detergent that can scratch or ruin the coating.
•Remove all the ingredients and crumbs from the lid, casing and baking compartment with a moist towel.
Never dip the appliance in water nor fill the baking compartment with water!
Never dip the appliance in water nor fill the baking compartment with water!Never dip the appliance in water nor fill the baking compartment with water!
Never dip the appliance in water nor fill the baking compartment with water! The lid can be removed for
easy cleaning. Remove the lid flap behind the lid hinge. You can then carefully remove the lid by pushing it
backwards. To replace it, act in the reverse order.
•Wipe the outside of the baking tin with a moist towel. The inside of the tin can be washed with hot water.
Please do not immerse it in water for longer period and do not use any washing-up liquid.
•Both the kneading pegs and drive shafts need to be cleaned immediately after use. If the kneading pegs
remain in the tin, it becomes difficult to remove them afterwards. In this case fill the container with warm
water and leave it to rest for 30 minutes. Then remove the kneading pegs.
•The baking tin has a nonstick coating. Do not use metal objects that can scratch the surface when cleaning
it. It is normal that the color of the coating changes over the course of time. This change does not alter ist
effectiveness in any way whatsoever.
•Before putting the appliance away for storage, make sure that it is perfectly cool, clean and dry. Put the
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Bomann cb 593 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Bomann cb 593 in the language / languages: English, German, Dutch, Polish, Portuguese as an attachment in your email.
The manual is 1,22 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
