364279
17
Zoom out
Zoom in
Previous page
1/84
Next page
21
Position the tube so that the liquid
is able to fl ow out while cleaning.
Insert the tip of the cleaning
balloon into the tube in the
arrowed direction and place the
end of the opposite tube in a
suitable container with warm water.
Thoroughly rinse out the tube repeatedly by fi rmly
squeezing the balloon.
Refi t the tube and close the cover.
NOTE
:
It is recommended to use hot water and a small amount
of washing-up liquid. In this case, the tube should be
rinsed again with clear, warm water in order not to
prevent impairment of the taste and foam formation.
Cleaning after emptying a 5 litre party keg
Each time a keg is emptied, the dispensing unit must be
thoroughly cleaned in addition to the collecting tray, drip
tray and tube. The cleaning balloon should be used for this
purpose.
Position the dispensing unit so that
the liquid is able to fl ow out while
cleaning.
Remove the cover located at the front below the beer
tap.
Open the beer tap and fi x it in this position by pulling
the tap handle until it locks.
Insert the tip of the cleaning balloon into the
dispensing tube in the arrowed direction and place
the end of the opposite tube in a suitable container
with warm water.
Thoroughly rinse out the dispensing tube by fi rmly
squeezing the balloon.
NOTE
:
It is recommended to use hot water and a small
amount of washing-up liquid. In this case, the
dispensing tube should be rinsed again with clear,
warm water in order not to prevent impairment of
the taste and foam formation.
Disinfectant cleaners in powder form for beer and
drinks systems are available from off-licences,
which are ideal for cleaning the beer dispenser.
ATTENTION!
The dispensing unit is not dishwasher proof.
If the dispenser is not used for an extended period,
it should be thoroughly cleaned beforehand.
Regular cleaning
Regularly clean the cooling chamber and all surfaces of
the dispenser with a moist cloth and small amount of mild
washing-up liquid.
ATTENTION!
Before cleaning the dispenser, always disconnect
the plug from the mains socket and never immerse
the dispenser in water!
The cooling chamber must not be fi lled with liquid
as this can cause permanent damage!
Troubleshooting
Problem Possible cause Remedy
The unit does not
switch on.
The plug is not
plugged into the
mains socket.
The main switch
is set to "0".
Plug the plug into
the mains socket.
Set the main
switch to "I".
No beer is
dispensed.
The 5 litre party
keg is empty
or there is not
a 5 litre party
keg in the beer
dispenser.
Place a new 5
litre party keg in
the dispenser.
The CO2
cartridge is
empty.
Change the CO2
cartridge.
The keg tap is not
tted. The keg
is not correctly
tapped.
Screw the keg tap
to the dispensing
unit. Tap the keg
correctly.
The tap handle
is not correctly
installed.
Install the tap
handle correctly.
Too much foam
is produced when
dispensing.
The 5 litre party
keg is not cold
enough.
Cool the 5 litre
party keg longer.
The 5 litre party
keg was shaken.
Allow the 5
litre part keg to
stand in the beer
dispenser for a
while.
The beer does
not fl ow freely out
of the tube.
Open the beer
tap fully.
The outlet tube
touches the glass
when dispensing.
Hold the glass
slightly further
away from the
outlet tube.
ENGLISH
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann bz 9482 cb at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann bz 9482 cb in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 6,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bomann bz 9482 cb

Bomann bz 9482 cb User Manual - English, German, Dutch, French, Italian, Polish, Spanish - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info