Manual Bomann BS 1949 (page 43 of 74) (English, German, Dutch, French, Italian, Polish, Spanish)

687988

Zoom out

Zoom in

1/74

BS1949ACB_IM 20.10.16

Nozzle Attachments (16) and (17)

You can attach these two nozzle attachments directly to the

hand unit or to the already installed suction pipe.

Connection at the Hand Unit

• Insert a nozzle attachment with the marking facing up into

the connection at the hand unit. It must audibly engage.

• To disconnect the nozzle attachment, press the release

(14) and pull out the attachment at the same time.

Connection to the Suction Pipe

You need the adapter (15) for connection to the suction pipe.

• Insert the adapter with the angular side into the lower end

of the suction pipe.

• Now you can slip a nozzle attachment onto the round side

of the adapter.

• For removal of the nozzle attachment and the adapter,

just pull the parts off.

Combined Crevice / Brush Nozzle

With this nozzle, you can selectively vacuum corners and

slots.

Use the nozzle with locked brush to prevent scratching of the

surface to be cleaned.

• For this, press the button and push

the brush to the end of the nozzle. It

must engage.

• Press the button again to unlock the

brush.

Upholstery Brush

This nozzle is especially good for gentle cleaning of larger

susceptible surfaces.

Assembly the Wall Holder

Inserting the Plug of the Power Supply Unit

If you want to use the wall holder also as the charging station,

attach the plug of the power supply unit rst. Refer to the

illustrations (A to C) on page 3.

NOTE:

• Turn the plug at the metal end, not at the cable. Use a

pliers if necessary.

• There is an opening at the rear of the wall holder. You

can turn the plug additionally with a nger through this

opening.

1. Set the plug of the power supply unit with the attened

side into the wall holder. (Fig. A)

2. Turn the plug of the power supply unit by 90 °. It must

sit solidly in the holder and sliding no longer shall be

possible. (Fig. B)

3. Fix the cable in the cable guide. (Fig. C)

Fastening the Wall Holder

WARNING:

Make sure beforehand whether there are cables in the wall

which could be damaged!

CAUTION:

Place the wall holder so that the appliance is not exposed

to direct sunlight or other heat sources.

NOTE:

A power outlet must be near.

1. Measure the height for the wall holder. Hold the vacuum

cleaner against the wall with the suction pipe and the oor

nozzle installed.

2. Hold the wall holder against the wall as shown on page 3.

Mark 2 drill holes.

3. Drill the holes and insert the wall plugs into the wall.

4. Insert the screws through the holes of the wall holder.

5. Tighten the screws with a screwdriver hand-tight.

Charging the Battery

1. Turn off the device.

2. Connect the power supply unit with the connection

socket (5). If you have prepared the wall holder as a

charging station, suspend the appliance from the wall

holder.

3. Connect the mains adapter to a certied wall socket.

Charge the device for approx. 5 hours before rst-time

use.

NOTE:

• The LED charge indication shows the charging sta-

tus of the rechargeable battery. (25 %, 50 %, 100 %)

• The appliance has electronic charge control, which

prevents overcharging.

• Charging has been completed when all 3 LEDs

are lit.

• The LEDs go out after a while.

• It is normal for the device to heat up during charging.

4. The rechargeable battery must be charged when the LED

charge indication shows only 25 % of capacity.

5. Disconnect the power supply unit from the outlet once the

rechargeable battery has been charged completely.

NOTE:

Even when switched off, the rechargeable battery dis-

charges continuously. If the device is out of use for a longer

period of time, charge the rechargeable battery at least

once every 6 to 12 weeks.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bomann BS 1949 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 5,7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bomann BS 1949 Manual

Product: