640549
29
Zoom out
Zoom in
Previous page
1/40
Next page
29 EN
Problem Cause Explanation / Suggestion
Water in the washer.
There may be some water in your
appliance when you receive it.
This is from the quality control
process and is normal.
It is not harmful to your washer. You
should run a “sanitary” cycle without
any clothes and laundry additives
before the first use of your washer.
Washer does not fill with
water or wash after the
program was selected
andthe«Start/Pause/
Cancel» button was
pressed.
Faucets may be turned off. Open the water faucets fully.
Water inlet hose may be folded.
Check the water inlet hose and
straighten if necessary.
Water inlet strainers might be
clogged.
Clean the water inlet strainers.
Is there power at the outlet?
Call an electrician and have the
power outlet / circuit breaker / fuse
checked.
Washer might be unplugged.
Plugthepowercordtoalive
electrical outlet.
Drain hose may be folded.
Check the drain hose and straighten
if necessary.
Washer may be in handwash,
wools or soak cycle.
Wait for a short time and tumbling
will start.
Drain pump filter or drain itself
may be clogged.
Clean the drain pump filter (See
«Cleaning the Washer» ). If the
house drain pipes are clogged, call a
plumber for assistance.
Door may not be closed properly. Close the loading door.
Washer does not drain
water / Washer drains
water slowly.
Drain hose may be folded.
Check the drain hose and straighten
if necessary.
Drain pump filter or drain itself
may be clogged.
Clean the drain pump filter (See
«Cleaning the washer» ). If the house
drain pipes are clogged, call a
plumber for assistance.
The water being taken in
is directly discharged.
Improper position of the drain
hose.
Connect the drain hose as described
in the user manual (See «Installation
Instructions, Drainage»).
No water can be seen
in the drum during
washing.
This is not a problem. The water
level is not visible from the
outside of the washer.
Washer stopped shortly
after the program cycle
started.
Washer can stop temporarily due
to low voltage.
It will resume operating when the
voltage is back to the normal level.
8 Troubleshooting
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blomberg WM 67120 NBL00 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blomberg WM 67120 NBL00 in the language / languages: English as an attachment in your email.

The manual is 1,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info