Manual Black Decker LM2000 (page 12 of 116) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

709484

Zoom out

Zoom in

1/116

ENGLISH

(Original instructions)

Also clean out any grass or debris which may be packed

around the discharge opening. Replace the grass catcher.

u If mower should start to vibrate abnormally, release bail

handle to turn mower off and remove safety key. Check

immediately for cause. Vibration is a warning of trouble.

Do not operate mower until a service check has been

made.

Refer to troubleshooting guide in manual.

u Always release bail handle to turn mower off when leaving

it unattended even for a short period of time.

Removing and installing blade

Warning! When reassembling the blade system, ensure each

part is reinstalled correctly, as described below.

Improper assembly of the blade or other parts of the blade

system may cause serious injury.

Warning! Release bail handle to turn mower off, wait for the

blade to stop, and unplug mower.

u Cut a piece of 2x4 wood (27) (about 610 mm) to keep

blade from turning while removing bolt (28).

u Wear gloves and proper eye protection.

u Turn the mower on its side. Be careful of sharp edges of

blade. Position wood and unscrew bolt with 9/16” wrench

(29) as shown in gure S.

u Note the orientation of each part as you remove it.

Remove nut (30). Pull off washer (31), the blade insulator

(32), and the blade (33) as shown in Figure T. Examine all

pieces for damage and replace if necessary.

Note: The fan should not be able to be removed.

u To reassemble, slide the blade (33) on. It can only be at-

tached to the fan in one direction and location. Line up the

D-shaped hole of the blade with the D-shaped post of the

fan, ensuring the writing on the blade faces out away from

the mower. Place the insulator (32) on the blade so that

the two outer ribs extend past the blade. Place the square

washer (31) on top of the insulator so that it sits inside of

the two outer ribs on the insulator. Replace the nut (30)

with the wide side against the washer.

u To tighten rmly, position the piece of wood as shown

in gure U to keep the blade from turning. Slide the bolt

through the washer and screw bolt into place. Tighten with

the wrench.

Blade sharpening

Keep blade sharp for best mower performance. A dull blade

does not cut grass cleanly. Use proper eye protection while

removing, sharpening, and installing blade. Ensure that safety

key and battery pack is removed.

Sharpening the blade twice during a mowing season is usually

sufcient under normal circumstances. Sand causes the

blade to dull quickly. If your lawn has sandy soil, more frequent

sharpening may be required.

Note: Replace bent or damaged blade immediately.

When sharpening the blade:

u Make sure blade remains balanced.

u Sharpen blade at the original cutting angle.

u Sharpen cutting edges on both ends of blade, removing

equal amounts of material from both ends.

To sharpen blade in a vise (g. V)

u Be sure the bail handle is released, the blade has stopped

and the mower is unplugged before removing the blade.

u Remove blade from mower. See instructions for removing

and installing blade.

u Secure blade (33) in a vise (36).

u Wear proper eye protection and gloves and be careful not

to cut yourself.

Carefully le the cutting edges of the blade with a ne

tooth le (39) or sharpening stone, maintaining the angle

of the original cutting edge. Check balance of blade. See

instructions for blade balancing. Replace blade on mower

and tighten securely.

Blade balancing

Check balance of the blade (35) by placing centre hole in

the blade over a nail or round shank screwdriver, clamped

horizontally in a vise. if either end of the blade rotates down-

ward, le along the sharp edge of that dropping end. Blade is

properly balanced when neither end drops.

Lubrication

No lubrication is necessary. Do not oil the wheels. They have

plastic bearing surfaces which require no lubrication.

Cleaning

Release bail handle (2) to turn mower off, let the blade come

to a stop and then remove safety key. Use only mild soap

and a damp cloth to clean the mower. Clean out any clippings

which may have accumulated on the underside of the deck.

After several uses, check all exposed fasteners for tightness.

Preventing corrosion

Fertilizers and other garden chemicals contain agents which

greatly accelerate the corrosion of metals. If you mow in areas

where fertilizers or chemicals have been used, the mower

should be cleaned immediately afterward as follows: Release

bail handle (2) to turn mower off and unplug mower. Wipe all

exposed parts with a damp cloth.

Maintenance

Your BLACK+DECKER corded/cordless appliance/tool has

been designed to operate over a long period of time with a

minimum of maintenance. Continuous satisfactory opera-

tion depends upon proper tool/appliance care and regular

cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in your tool/appliance

and charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

u Regularly use a blunt scraper to remove grass and dirt

from the underneath of the guard.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker LM2000 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,04 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker LM2000 Manual

Product: