Manual Black Decker LM2000 (page 10 of 116) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

709484

Zoom out

Zoom in

1/116

ENGLISH

(Original instructions)

Use of extension cords

Make sure the extension cord is in good condition before us-

ing. Always use the proper size extension cords with the tool –

that is, proper wire size for various lengths of cord and heavy

enough to carry the current the tool will draw.

Use of an undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. To reduce the likeli-

hood of disconnection of lawn mower cord from the cord set

during operating:

u Make a knot as shown in Figures A and A1, or.

u Use one of the plug-receptacle retaining straps or connec-

tors described in this manual (Figure B).

Attaching extension cord (gure B)

An extension cord retainer (12) that prevents the cord from

coming unplugged is built into the switch handle.

u To use this feature, simply double the extension cord

about 203mm from the end, and insert it into the

opening (13) as shown in gure B.

u Push the extension cord into the two holding slots (14) to

reinforce the hold.

u Gently tug on the cord to insure that it is rmly in the

mower’s retainer.

u Plug the receptacle end of the extension cord into the

power cord and plug in extension cord.

Warning! Don’t Abuse Cord – Never pull lawn mower by cord

or yank it to disconnect from receptacle. Keep cord from heat,

oil, and sharp edges.

Assembly

Warning! Before assembly, make sure the bail handle is

released and the mower is unplugged.

Attaching lower handle

u Lift lower handle (4) into place making sure the arrow (15)

on the base of the mower lines up with 1 or 2 on the base

of the handle (16) (inset of Figure C)

Note! Ensure each side of the lower handle is set on the same

number. The arrow must be lined up with 1 or 2 for operation.

u Close the handle height adjust levers (6) as shown in

Figure C. As you close each, make sure the teeth are

engaged as shown in Figure D.

u If the connection between the handle and lever is too tight

or loose, open the lever and adjust the depth of the lever

by turning the lever. Close it again until the teeth are fully

clasped and each lever stays securely closed.

Attaching upper handle (g. E)

u Remove the upper-handle attachment levers (5), nuts

(17), and washers (18) from the handle.

u Line up the holes on the bottom of the upper handle (3)

with the holes on the top of the lower handle (4).

Note: Make sure the cord is located on the front of both

handles. If it is not it may result in the cord tangling and the

inability to easily store the mower.

u From the outside of the upper handle (3), slide the lever

bolt through the holes.

u Slide the washer over the bolt of the lever and loosely

assemble the entire assembly with the nut.

u Rotate the upper handle into its operating position.

u Close the lever. If it is too tight or too loose, open the lever

and the nut to adjust the clamping. Check the levers by

closing them. They should be tight enough so the handles

are held rmly, but loose enough so the levers can be fully

closed. Adjust by opening the lever and turning the nut

until the handles are secured.

Securing the motor cable (g. F)

Warning: Attach cable so that it does not become stretched or

pinched in the joints of the handles during use or folding. This

can cause damage to the cord.

The motor cable (19) has to be xed to the handles using the

cable restraints (20) that are already attached to the handle.

To clip the cable to the handle:

u Place the handles in operating position, see “Attaching

lower handle” section.

u Run the cable up the front of the lower and upper handles.

u Pull back the cable restraint.

u Slide the motor cable under the clip and ensure it is fully

held in place by the restraint.

Bagging

u Ensure the side discharge attachment (24) (g. I) and the

mulching insert (23) (g. H) are removed from the mower

before bagging.

u Lift the rear door cover (9) and place the grass collection

bag (8) onto the mower so the bag hooks (21) rest on the

lugs (22) as shown in gure G. Then lower the rear door

cover.

Mulching

u Ensure the side discharge attachment (27) and the collec-

tion bag (8) are not attached.

u Lift the rear door cover (9) and slide the mulching insert

(23) fully into the mower as shown in gure H.

u ensure the rear door cover fully closes before turning

mower on.

Side discharge

u Ensure the collection bag (8) is removed.

u Lift the rear ap (9) and slide the mulching insert (23) fully

into the mower as shown in gure H.

u Lift the side ap (25) and hook side discharge attachment

(24) onto the mower as shown in gure I.

u Release the side ap and ensure the attachment holds in

place before turning mower on as shown in the insert of

gure I.

Operation

Warning! Let the mower work at its own pace. Do not

overload.

Adjusting handle height (fIg. J)

u Open both lower-handle attachment levers (6).

u Adjust the handle so the arrow (15) on the base of the

mower lines up with 1, or 2 on the base of the handle

(16). ensure the handle is set to the same number on both

sides of the mower.

u Close both levers and ensure the handle is rmly latched

and the teeth are engaged as shown in inset.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker LM2000 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,04 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker LM2000 Manual

Product: