568800

Beurer IPL 9000 plus Manual

38
Zoom out
Zoom in
Previous page
1/124
Next page
38
8.6 Care after facial treatment
• Apply a soothing lotion such as aloe vera.
• Do not use exfoliators, whitening lotions or similar products for at least 24hours, as this could irritate
the treated skin.
• For at least 48 hours after the treatment, avoid more than 15 minutes of direct exposure to the sun. If
recently treated skin is exposed to sunlight during this period, sun protection with SPF30 or higher
must be applied.
• Do not remove hair on the treated areas using wax or tweezers.
Remember that it may take a complete hair growth cycle for hair removal to be complete.
9. Care and maintenance of the beurer SalonPro System
9.1 Cleaning the beurer SalonPro System
After each hair removal session, it is recommended that you clean your beurer SalonPro System, paying
particular attention to the light area.
IMPORTANT
Never immerse the beurer SalonPro System or any of its parts in water!
• Before cleaning, unplug the mains plug of the beurer SalonPro System.
• Use a clean, dry cloth and cleaning agent especially intended for electronic devices to gently wipe
the surface of the beurer SalonPro System, paying particular attention to the light surface.
9.2 Replacing the cartridge
The cartridge has a life cycle of up to 100.000 light pulses. When the cartridge reaches 80% of its life
cycle, the indicator lamp for „Cartridge empty“ starts to slowly flash red. When 90% is reached, the
indicator lamp flashes at a faster pace. Once all the cartridge‘s light pulses are used up, no further light
pulses are generated. The indicator lamp for „Cartridge empty“ then continuously illuminates red.
Changing to a new cartridge:
1. Switch off the device and remove the mains plug from the socket.
2. Hold the used cartridge on both sides and pull it out in one smooth motion. Do not use force. Dis-
pose of the used cartridge.
3. Unpack the new cartridge and plug it in.
10. Trouble-shooting
"My beurer SalonPro System cannot be switched on"
•
Ensure that the mains cable is correctly connected to the beurer SalonPro System device.
•
Ensure that the mains cable is inserted into a wall socket.
"No light pulse is emitted when I press the trigger button"
• Ensure that the device is in full contact with the skin and that the light area is pressed onto the skin
evenly and firmly. For your safety, the trigger button only activates a pulse if the light area is pressed
firmly against the skin.
•
Check the indicator lamp. If the indicator lamp on the applicator is illuminated red, this indicates that
your skin colour, as measured by the skin colour sensor, is too dark for safe application. Test the
device on another part of your body or contact beurer SalonPro System Customer Services.
If the
indicator lamp
on the
applicator
is illuminated orange, this indicates that the contact with the
skin, as measured by the skin contact sensor, is insufficient. Increase the level of contact with the
skin
or contact beurer SalonPro System Customer Services.
• The cartridge has a life cycle of up to 100.000 light pulses. When the cartridge reaches 80% of its life
cycle, the indicator lamp for „Cartridge empty“ starts to slowly flash red. When 90% is reached, the
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Beurer IPL 9000 plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Beurer IPL 9000 plus in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 7,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info