Manual Berner GA101 (page 7 of 68) (English, German, Dutch, French)

474160

Zoom out

Zoom in

1/68

Dear Customer,

Thank you for choosing this quality product from our company.

Please keep these instructions safe for later reference!

Please carefully read and follow these instructions. They provide

you with important information on the safe installation, operation

and correct care / maintenance of your garage door operator,

thus ensuring that this product will give you satisfaction for

many years to come.

Please observe all our safety notes and warnings, specifically

headed ATTENTION, CAUTION or Note.

1 IMPORTANT NOTES

ATTENTION

Installation, maintenance, repair and dismantling

of the garage door operator may only be carried

out by specialists.

Note

The inspection log book and instructions for safe handling

and maintenance of the door system must be placed at

the disposal of the end user.

1.1 Important safety instructions

CAUTION

Incorrect installation or handling of the operator

could result in serious injury. For this reason, it

is important to follow all the instructions in this

manual.

This garage door operator is designed exclusively for

impulse operation of spring-balanced up-and-over and

sectional doors in the non-commercial sector. Use in

the commercial sector is not permitted!

Please observe the manufacturer's specifications regarding

the door and operator combination. Possible hazards as

defined in EN 12604 and EN 12453 are prevented by the

design itself and by carrying out installation in accordance

with our guidelines. Door systems used by the general

public and equipped with a single protective device, e.g.

force limit, may only be used when monitored.

1.1.1 Warranty

We shall be exempt from our warranty obligations and

product liability in the event that the customer carries

out his own structural changes or undertakes improper

installation work or arranges for same to be carried out

without our prior approval and contrary to the installation

guidelines we have provided. Moreover, we shall accept no

responsibility for the inadvertent or negligent operation of

the operator and accessories nor for the improper main-

tenance of the door and its counterbalance mechanism.

Batteries and light bulbs are also not covered by the

warranty.

Note

Should the garage door operator fail, a specialist must be

immediately entrusted with its inspection / repair.

1.1.2 Checking the door / door system

The design of the operator is not suitable nor intended for

the opening and closing of heavy doors, i.e. doors that

are difficult or impossible to open and close manually.

Before installing the operator, it is therefore neces-

sary to check the door and make sure that it can

also be easily moved by hand.

To do this, raise the door approx. 1 metre and then let it

go. The door should retain this position, moving neither

up nor down. If the door moves in any of the two direc-

tions, there is a risk that the compensating springs are

defective or incorrectly adjusted. In this case increased

wear and malfunctioning of the door system can be

expected.

CAUTION: Danger!

Do not attempt to change, re-adjust, repair or

move the compensating springs for the door's

counterbalance mechanism or their holders. The

springs are under considerable tension and can

cause serious injury. In addition, check the entire

door system (pivots, door bearings, cables,

springs and fastenings) for wear and possible

damage.

Check for signs of corrosion or fractures. The

door system may not be used if repair or adjust-

ment work needs to be carried out. Always

remember that a fault in the door system or a

misaligned door can also cause severe injury.

Note

Before installing the operator, and in the interests of your

own safety, make sure that any work needed on the door's

compensating springs is carried out by a qualified garage

door specialist. Only correct fitting and maintenance in

compliance with the instructions by a competent / specialist

company or a competent / qualified person ensures safe

and flawless operation of the system.

1.2 Important instructions for safe installation

The specialist carrying out the work must ensure that

installation is conducted in compliance with the prevailing

national regulations on occupational safety and those

governing the operation of electrical equipment. In

the process, the relevant national guidelines must be

observed.

Possible hazards as defined in DIN EN 13241-1 are pre-

vented by the design itself and by carrying out installation

in accordance with our guidelines. Any further processing

must ensure that the national regulations governing the

operation of electrical equipment are complied with.

1.2.1 Before installing the garage door operator, check

that the door is in a flawless mechanical condition and

is correctly balanced, so that it can be easily moved by

hand (EN 12604). Further check whether the door opens

and closes in the proper manner (see section 1.1.2).

In addition, any of the door's mechanical locks and

latches not needed for power operation of the garage

door should be immobilized. Included here in particular

are the latching mechanisms of the door lock (see section

3.2.1/3.2.2).

The garage door operator is designed for use in dry

buildings and therefore may not be installed outdoors.

The garage ceiling must be constructed in such a way

as to guarantee safe, secure anchoring of the operator.

In the case of ceilings that are too high or too lightweight,

the operator must be attached to additional braces. ➤

ENGLISH

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Berner GA101 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 5,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Berner GA101 Manual

Product: