810831
48
Zoom out
Zoom in
Previous page
1/72
Next page
EN
39
Disk brakes:
The wheel can be removed without any further
preparation.
Please note: when tting the wheel, the disk
must be slotted between the brake linings of
the brake calliper and ultimately be centred
without contact.
Bedding in disc brakes
New disc brake pads and brake discs have to
be bedded in carefully before you ride the bike
for the rst time. This process optimises brake
performance.
The bedding-in process involves
sharp braking. You should be famil-
iar with braking power and the use
of disc brakes. Sharp braking without being
familiar with brake performance and the op-
eration of disc brakes, can lead to accidents
causing severe or fatal injury. If you are un-
sure, you should have a qualied bicycle/
pedelec mechanic perform the bedding-in
process for you.
Proceed as follows:
To bed in the brakes, accelerate the pedelec to
30 km/h and then bring the pedelec to a halt by
applying maximum braking. Repeat this proce-
dure approx. 20 times. For optimal results, the
wheels should not be allowed to lock.
Please do not touch the brake disc
while it is rotating or directly after
braking. Otherwise injuries or burns
may result.
Source: Shimano® techdocs
Air bubbles in hydraulic disc brakes
Avoid permanently braking for long
periods, as can be the case during
long, steep descents. Otherwise,
bubbles may form and a total failure of the
braking system may occur. Severe falls and
injuries may result.
The brake lever may not be applied
if the pedelec is on its side or upside
down. Otherwise air bubbles can
enter the hydraulic system which could
cause the brakes to fail. After transporting
the pedelec, check if the pressure point of
the brakes seems softer than before. Then
slowly apply the brake a few times. By doing
this, air can be discharged from the brake
system. If the pressure point remains soft,
please do not use your pedelec and ask a
specialist to remove the air from the brake.
You can avoid this problem by ap-
plying the brake lever before trans-
porting your pedelec and then xing
it in this position using a strap. This prevents
air from entering into the hydraulic system.
When you come to cleaning the
braking system, please rst read
and follow the instructions provided
by the component manufacturer.
In particular, brake discs are subject
to wear. Have these safety-related
components regularly checked for
wear and changed as required by your spe-
cialist retailer.
Source: Shimano
® techdocs
Please do not touch the brake disc
while it is rotating or directly after
braking. Otherwise injuries or burns
may result.
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Benno Pedelec - E-bike at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Benno Pedelec - E-bike in the language / languages: English as an attachment in your email.

The manual is 3.33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Benno Pedelec - E-bike

Benno Pedelec - E-bike User Manual - Dutch - 74 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info