577368
45
Zoom out
Zoom in
Previous page
1/58
Next page
08/ 2012 45 / 58
BENNING ST 750 A
- The reading process starts. Wait until the orange LED goes out and an acoustic signal is
emitted.
- The device searches for the ID no. in the internal database.
- Confirm the queries. If necessary, create the test sample.
- The data record is displayed.
An incorrect reading process will be signalled by two consecutive acoustic signals. Repeat
the process!
Reading data completely from the transponder: (inventory data and measured values)
- Remove the SD memory card!
- Delete the database from the internal memory. For this, select an empty field from the pull-down
menu.
- Hold the scanning window of the RFID reader over the RFID transponder and press the button
on the bottom of the scanner.
- The reading process starts. Wait until the orange LED goes out and an acoustic signal is
emitted.
- Confirmthequery"ReadingdatafronRFIDtransponder".
- Hold the scanning window of the RFID reader over the RFID transponder and press the button
on the bottom of the scanner.
- The reading process starts. Wait until the orange LED goes out and an acoustic signal is
emitted.
- The inventory data and measured values are read from the RFID transponder.
- The inventory data are displayed.
- Press <Back> and select the test date to display the measured values.
An incorrect reading process will be signalled by two consecutive acoustic signals. Repeat
the process!
18. Bluetooth Printer (Optional)
Whenconnectingtheprinter,rstswitchofftheBENNINGST750AApplianceTester!
BENNING ST 750 A
53 / 68
18. Bluetooth Drucker (Option)
Bei Anschluss des Druckers, zuerst den Gerätetester BENNING ST
750A ausschalten!
1
2
3
4
18.1. Batterien einsetzen / entfernen
Schalten Sie den Drucker aus.
Auf der Rückseite die Schraube des Batteriefachs entfernen.
Batterieabdeckung entfernen
Batterien austauschen.
Batterieabdeckung montieren.
18.2. Papierrolle einsetzen
Schalten Sie den Drucker aus.
Ziehen Sie den Arretierhebel vor und klappen die Abdeckung für das
Papierfach auf.
Papierrolle einlegen und den Anfang der Papierrolle über die Abreißkante
ziehen.
Abdeckung zuklappen, so dass die Arretierung einrastet.
18.3. Spezifikation Bluetooth Drucker
Benning Teile-Nr.:
044150
Schnittstelle:
RS-232-Serielle-Schnittstelle / über RJ12 Anschluss
Drahtlose (Wireless) Verbindung:
Bluetooth
®
Betriebsspannung:
5V, versorgt durch internen Akku, oder externer Spannungsversorgung
18.4. Bedienung Bluetooth Drucker
Die Konfiguration ist nur bei Erstinbetriebnahme notwendig, die
Druckerdaten werden im Gerätetester gespeichert und bei erneuter
Verwendung muss nur der Bluetooth Dongle eingesteckt und der Drucker
eingeschaltet werden.
Erst-Konfiguration:
Gerätetester BENNING ST 750A ausschalten
Bluetooth Dongle an den Gerätetester BENNING ST 750A
anschließen (USB-A-Buchse).
Gerätetester einschalten
Drucker durch drücken der Einschalttaste einschalten.
aus dem Hauptme <Setup> / <Systemeinstellung> / <Drucker> zur
Druckerverwaltung
Drucker <Suchen>
Geräte-Name: Eingabefeld anklicken und Drucker auswählen.
Druckername beginnt mit „ASL AP…“
Pin-Code eingeben (Pin-Code: 1234)
<Verbinden>
Reset durchführen
Gerätetester Benning ST 750A startet neu
Drucker ggf. neu einschalten.
Nach Durchlaufen einer Prüfung bzw. via Datenbank kann über
<Messwertanzeige> / <Testende> dass Prüfergebnis gedruckt
werden <Drucken>
Gedruckt wird:
Prüfgerät, Ident-Nr., Bezeichnung, Prüfdatum, Nächster Prüftermin,
Testergebnis, Messwerte, Prüffirma, Prüfer, Bemerkung und der Barcode
zum Prüfobjekt.
(1) Arretierhebel
(2) Ein- / Ausschalttaste
(3) Kontrollleuchte
(4) Bluetooth Dongle
1 stopping lever
2 ON / OFF button
3 control lamp
4 Bluetooth dongle
18.1 Inserting / Removing the Batteries
- Switch the printer OFF.
- Remove the screw of the battery compartment on the back.
- Remove the battery compartment cover.
- Replace the batteries.
- Put the battery compartment cover back onto the device.
18.2 Inserting a Paper Roll
- Switch the printer OFF.
- Pull the stopping lever forward and open the cover of the paper compartment.
- Insert the paper roll and pull the front end of the paper roll over the tear-off edge.
- Close the cover so that the stopping lever locks into place.
18.3 Bluetooth Printer Specification
Benning part no.:
044150
Interface:
RS232 serial interface / via RJ12 connection
Wireless connection:
Bluetooth®
Operating voltage:
5V, supplied by an internal storage battery or via an external mains supply unit / charger
18.4 Operating the Bluetooth Printer
Congurationisonly required for initial commissioning. The printer data are stored in
the appliance tester. For using it again, simply insert the Bluetooth dongle and switch
on the printer.
Initial configuration:
- Switch the BENNING ST 750 A Appliance Tester OFF.
- Connect the Bluetooth dongle to the BENNING ST 750 A Appliance Tester (USB-A jack).
- Switch the appliance tester ON.
- Switch the printer ON by pressing the ON / OFF button.
- In the main menu, select <Setup> / <System Settings> / <Printer> to get to the printer
management.
- <Search> the printer.
- Device name: Tap the input field and select the printer.
Printernamestartswith"ASLAP…".
- Enter the PIN code (PIN code: 1234)
- <Connect>.
- Carry out a reset.
- The BENNING ST 750 A restarts.
- If necessary, switch the printer ON again.
- After a test or via the database, it is possible to print the test result by selecting <Measured
Values> / <End of Test> and pressing <Print>
The following data are printed:
Tester, ID no., designation, test date, next test, test result, measured values, test company, test
person, comment and the barcode of the test object.
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Benning ST 750A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Benning ST 750A in the language / languages: English as an attachment in your email.

The manual is 7,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Benning ST 750A

Benning ST 750A User Manual - German - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info