577368
44
Zoom out
Zoom in
Previous page
1/58
Next page
08/ 2012 44 / 58
BENNING ST 750 A
17. RFID Reader (Optional)
RFIDisamethodforautomaticandelectronicidenticationofobjectsperradiotechnology. For
identicationoftheobject,thedatacanbereadoutbywirelesstechnologyviaaradiofrequency
channel. A marked object only sends its data, if the reader calls the transponder. An RFID system
consists of two components: a transponder and a reader. The transponder (in the following referred
toas"tag")istheactualdatacarrier.
It is possible to read it and to write on it without any contact by means of radio technology. The tag
stores data of the tag and of the connected object. The reader consists of a reader/writer unit with
antenna. The reader reads data of the tag and writes data to the tag. The reader is provided with a
USB 2.0 interface to transmit the received data to the BENNING ST 750 A Appliance Tester.
For installation of the tags, it has to be observed that metallic surfaces strongly interfere with the
radio connection. Therefore, do not install them directly onto metal or a metal housing. Data ex-
change between reader and transponder does not require direct contact (even not a visual contact).
Barcode labels can be exchanged by means of RFID transponders. The device communicates with
passive HF transponders with 13.56 MHz. The reading process is started by pressing a button. If
atransponderhasbeenidentied,thisisconrmedbyanacousticsignal.Itisnotnecessaryto
conguratetheRFIDreader.
WhenconnectingtheRFIDreader, rstswitchofftheBENNINGST750AAppliance
Tester! Do not remove / insert the RFID reader during operation. Always switch off the
devicerst!
In case of faults, switch off the appliance tester. Remove the RFID reader, reconnect it
and then switch on the appliance tester.
17.1 RFID Reader Specification
Benning part no.:
009370
Interface:
USB 2.0 interface
Operating voltage:
5V, supplied by USB interface of BENNING ST 750 A
Supported RFID transponders:
13.56MHz,seechapter21"OptionalAccessories"
Reading range:
typ. 80 mm, depending on transponder
Typical reading time:
100 ms
Current consumption:
typ. 60 mA (passive mode)
typ. 120 mA (active mode)
Operating temperature:
0 °C to 50 °C
Storage temperature:
- 10 °C to 60 °C
Relative humidity:
20 % - 85 %
Protection category:
IP30
Dimensions:
approx. 165 x 110 x 80 mm
17.2 Operating the RFID Reader
The RFID reader can be used in combination with the following device groups: BENNING ST 750 A
For reading / writing processes, wait until the orange LED goes out.
An incorrect writing process will be signalled by two consecutive acoustic
signals. Repeat the process!
Commissioning:
- Switch the BENNING ST 750 A Appliance Tester OFF.
- Connect the RFID reader to the BENNING ST 750 A Appliance Tester (USB-A jack).
- Switch the BENNING ST 750 A Appliance Tester ON.
- MakesurethattheRFIDlamp("Power")switcheson.
Writing onto the transponder: (inventory data)
- Create the inventory data of a test sample in an internal database or select an existing test
sample (ID no.).
- <Select> <Save> and confirm the queries.
- Message: "Doyou want to save the data record on theRFID transponder?".Confirm with
<Yes>.
- The orange LED of the RFID reader flashes.
- Hold the scanning window of the RFID reader over the RFID transponder and press the button
on the bottom of the scanner.
- The writing process starts. Wait until the orange LED goes out and an acoustic signal is emitted.
- The data are saved on the RFID transponder.
An incorrect writing process will be signalled by two consecutive acoustic signals. Repeat
the process!
Writing onto the transponder: (measured values)
- Carry out the test.
- When the test result is displayed, select <Save>.
- Confirm the queries.
- Message: "Doyou want to save the data record on theRFID transponder?".Confirm with
<Yes>.
- The orange LED of the RFID reader flashes.
- Hold the scanning window of the RFID reader over the RFID transponder and press the button
on the bottom of the scanner.
- The writing process starts. Wait until the orange LED goes out and an acoustic signal is emitted.
- The data are saved on the RFID transponder.
An incorrect writing process will be signalled by two consecutive acoustic signals. Repeat
the process!
Reading the ID no. from the transponder and searching in internal database:
- Hold the scanning window of the RFID reader over the RFID transponder and press the button
on the bottom of the scanner.
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Benning ST 750A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Benning ST 750A in the language / languages: English as an attachment in your email.

The manual is 7,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Benning ST 750A

Benning ST 750A User Manual - German - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info