656672
16
Zoom out
Zoom in
Previous page
1/24
Next page
16
ULTRALINK UL2000M
For the Auto Mute function to work, it has to be activated on both the transmitter and the
receiver!
Activating/deactivating the Auto Mute function
1. Engage MUTE. The transmitter can now be switched into the programming mode.
2. Turn the selection switch to 0 and confirm your selection by keeping the POWER switch pressed for 2
seconds. As a confirmation, the LED blinks slowly once and then once again with medium tempo. The
transmitter is now in the programming mode and waits for you to enter a one-digit number.
3. Select one of the following two digits on the selection switch:
Activate Auto Mute: select 7
Deactivate Auto Mute: select 8
If a valid selection is made, the LED blinks quickly once to confirm your selection. This way, you can be
sure that a correct value is entered (in regard to preset, MicGain and Auto Mute selection) even before
confirming your selection.
Selecting the values 1 through 4 changes the preset settings (ch. 3.2.4). Selecting 5 or 6
changes the Mic Gain settings (ch. 3.2.5). Values 9 and 0 are invalid.
4. Confirm your selection by briefly pressing the POWER button.
5. If the selection you made is valid, the LED blinks quickly once again. An invalid selection is indicated
with 5 quick blinks, and the unit is immediately no longer in the programming mode. In this case, start
anew with step 2.
After a brief break, a second blink code is given:
Auto Mute activated: the LED blinks once at middle tempo.
Auto Mute engaged: the LED blinks twice at middle tempo.
If no entry is made for more than 5 seconds (either on the selection switch or by pressing the
POWER button), the LED blinks quickly 5 times, and the programming mode is aborted.
6. After a second brief blink break, an additional blink code is given as a confirmation:
Two slow blinks signal that the Auto Mute setting was changed. The transmitter leaves the
programming mode.
If the setting for Auto Mute could not be stored, the LED blinks quickly 5 times. In this case, start
anew with step 2.
7. Disengage MUTE.
3.2.7 Turning the microphone off
To turn of the transmitter, keep the POWER button pressed for 2 seconds. A long blink confirms that
microphone is being turned off.
The transmitter stores the frequency and the channel settings. These parameters are restored
to these same values the next time you turn the unit on.
3.3 Status query
While you are using your microphone, you may want to check the “transmission channel,” “battery condition,”
“transmission frequency,” “preset,” “Mic Gain” and “Auto Mute” parameters. The status of these parameters
can be checked without having to turn the microphone off and back on.
3.3.1 Battery condition and transmission channel
1. Turn the selection switch to 0. The position of the MUTE switch does not matter.
2. Briefly press the POWER button.
3. Just like when powering the microphone on, the microphone status is indicated with medium-tempo
blink codes:
battery condition: 1 = battery is nearly empty . . . 5 = battery is fully loaded
selcted channel: 1 = channel 1 is selected. . . 8 = channel 8 is selected
3. ULM2000 MICROPHONE
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer Ultralink UL2000M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer Ultralink UL2000M in the language / languages: English as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer Ultralink UL2000M

Behringer Ultralink UL2000M User Manual - German - 24 pages

Behringer Ultralink UL2000M User Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info