656672
15
Zoom out
Zoom in
Previous page
1/24
Next page
15
ULTRALINK UL2000M
If no entry is made for more than 5 seconds (either on the selection switch or by pressing
the POWER button), the LED blinks quickly 5 times, and the programming mode is aborted.
6. After a second brief blink break, an additional blink code is given as a confirmation:
Successful loading of a preset is signaled with two slow blinks. The unit leaves the programming
mode.
If the preset could not be loaded, the LED blinks quickly 5 times. In this case, start anew with
step 2.
7. After setting the desired preset, disengage the MUTE switch.
3.2.5 Mic Gain
You have the option to adjust the ULM2000 to the level of the signal being transmitted. If you talk very
softly into the microphone, we recommend the “High Gain” setting; if the sound is loud, select “Low
Gain.” This way, optimal transmitter drive is achieved.
1. Engage MUTE. The transmitter can now be switched into the programming mode.
2. Turn the selection switch to 0 and confirm your selection by keeping the POWER button pressed for 2
seconds. As a confirmation, the LED blinks slowly once and then once again with medium tempo. The
transmitter is now in the programming mode and waits for you to enter a one-digit number.
3. Select one of the following two digits on the selection switch:
Low Gain: select 5
High Gain: select 6
If a valid selection is made, the LED blinks quickly once to confirm your selection. This way, you can be
sure that a correct value is entered (in regard to preset, MicGain and Auto Mute selection) even before
confirming your selection.
Selecting the values 1 thru 4 changes the preset settings (ch. 3.2.4). Selecting 7 or 8 changes
the Auto Mute settings (ch. 3.2.6). Values 9 and 0 are invalid.
4. Confirm your selection by briefly pressing the POWER button.
5. If the selection you made is valid, the LED blinks quickly once again. An invalid selection is indicated
with 5 quick blinks, and the unit is immediately no longer in the programming mode. In this case, start
anew with step 2.
After a brief break, a second blink code is given: The LED blinks according to the value selected (for
example, in this case 3 times) with medium tempo.
Low Gain: the LED blinks once with medium tempo.
High Gain: the LED blinks twice with medium tempo.
If no entry is made for more than 5 seconds (either on the selection switch or by pressing the
POWER button), the LED blinks quickly 5 times, and the programming mode is aborted.
6. After a second brief blink break, an additional blink code is given as a confirmation:
Successful loading of a preset is signaled with two slow blinks. The transmitter leaves the
programming mode.
If the setting for Mic Gain could not be stored, the LED blinks quickly 5 times. In this case, start
anew with step 2.
7. Disengage MUTE.
3.2.6 Auto Mute
If the transmitter is turned on, off or switched to another channel without first muting the receiver, or if the
transmission fails due to weak batteries, audible noise will result. Even if the squelch circuit is turned on at
the receiver end, it still requires some time to react, and such noise can not be suppressed safely.
To bridge this latency time, the ULM2000 offers a practical Auto Mute function:
When the ULM2000 is being turned off, when you are switching channels or during low-battery indication,
an inaudible send signal is being transmitted.
The ULR2000 recognizes this signal and automatically mutes the output before the transmitter is
actually turned off, switched to another channel or before it powers down on its own due to
battery charge being too low.
3. ULM2000 MICROPHONE
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer Ultralink UL2000M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer Ultralink UL2000M in the language / languages: English as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer Ultralink UL2000M

Behringer Ultralink UL2000M User Manual - German - 24 pages

Behringer Ultralink UL2000M User Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info