Manual Behringer EXPANSION CARD X-MADI (page 6 of 15) (English, German, French, Portuguese, Spanish)

660554

Zoom out

Zoom in

1/15

Warning

Failure to observe the following warnings may

lead to fatality or serious injury from re or

electric shock.

Before installing the card, you must refer to the owner’s

manual of the host device or to behringer.com to verify that

your host device supports this card, and to verify the number

of cards that can be installed in combination with other

BEHRINGER or third-party cards.

• Do not attempt to disassemble or modify the card.

Donot apply excessive force to board connectors or

other board components. Mishandling of board may

lead to shock, re hazard, or equipment failure.

• Disconnect the power cable from the main unit before

installing this card to eliminate shock hazard.

Caution

Failure to observe the following precautions may

lead to personal injury, or may result in damage

to equipment or other property.

• Do not touch the board’s metallic leads (pins)

whenhandling the card. Pins are sharp and may

causeinjury.

• The card is electrostatic-sensitive.

Before handling the card, you should briey

touch the main unit’s metal casing with

your bare hand so as to drain o any static

charge from your body. BEHRINGER assumes no

responsibility for data loss, equipment damage,

or injury caused by inappropriate handling or usage.

1. IMPORTANT NOTICE: DO NOT MODIFY

THIS UNIT! This product, wheninstalled as indicated

in the instructions containedin this manual, meets FCC

requirements. Modications not expressly approved by

BEHRINGER may void your authority, granted by the FCC,

to use theproduct.

2. IMPORTANT: When connecting this product to

accessories and/or another product, use only high quality

shielded cables. Cables supplied with this product MUST be

used. Follow all installation instructions. Failure to follow

instructions could void your FCC authorization to use this

product in the USA.

3. NOTE: This product has been tested and found to

comply with the requirements listed in FCC Regulations,

Part 15 for Class “B” digital devices. Compliance with these

requirements provides a reasonable level of assurance that

your use of this product in a residential environment will not

result in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in

the users manual, may cause interference harmful to the

operation of other electronic devices. Compliance with FCC

regulations does not guarantee that interference will not

occur in all installations. If this product is found to be the

source of interference, which can be determined by turning

the unit “OFF” and “ON”, please try to eliminate the problem

by using one of the following measures: Relocate either this

product or the device that is being aected by the interference.

Utilize power outlets that are on dierent branch circuits

(circuit breaker or fuse) or install AC line lters. In the case of

radio or TV interference, relocate/reorient the antenna. If the

antenna uses 300Ohm ribbon cable, use coaxial cable instead.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to distribute

this type of product. If you can not locate the appropriate

retailer, please contact BEHRINGER customer service.

FCC INFORMATION U.S.A.

1. Introduction

The X-MADI card is a multichannel audio interface expansion

card for the X32 series of digital mixers. It provides 32 channels

of MADI/AES10 input and output via bre-optic or coaxial cables.

This provides very long cable runs up to 2 km with ber-optic

connection and allows redundancy when combined with BNC

coaxial connectors.

2. Installation

Before you install the X-MADI card in the expansion slot of the

X32 console, you must check behringer.com to verify whether the

console rmware supports that card.

Caution – before installing the X-MADI card into the console,

you must make sure that the console’s power switch is turned o.

Malfunctions or electrical shock may occur otherwise.

1. Make sure that the mixer’s power is turned o.

2. Loosen the screws left and right that fasten the slot,

thenremove the slot cover or currently-installed card and

keep it in a safe place.

3. Before removing the X-MADI card from its protective bag,

we recommend touching the grounded metal chassis of the

console to prevent electrostatic discharges aecting the

sensitive electronic components. It is generally a good idea

to hold the card either by the face plate or by the two small

handles, but never touching the components on the circuit

board directly.

4. Align both edges of the card with the guide rails inside the

slot and carefully insert the card into the slot. Push the card

all the way into the slot to ensure that the contacts of the

card are correctly inserted into the connector inside.

5. Fasten the card using the included screws. Be aware that

damage or malfunctions may occur if the card is

not fastened.

Requirements

X32 Series console with rmware version 2.0 or higher.

10 11Quick Start GuideEXPANSION CARD X-MADI

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Behringer EXPANSION CARD X-MADI in the language / languages: English, German, French, Portuguese, Spanish as an attachment in your email.

The manual is 1,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Behringer EXPANSION CARD X-MADI Manual

Product: