765605

BeamZ 154.062 - DMX-024PRO Manual

8
Zoom out
Zoom in
Previous page
1/11
Next page
EXAMPLE: PROGRAMMING A LINEAR RUNNING LIGHT EFFECT
1) Switch the programming mode on (press RECORD/SHIFT and buttons 1, 5, 6 and 8).
2) Set both MASTER slider controls to the maximum (A upwards, B downwards).
3) Select mode 1-24 single via the MODE SELECT button (the green LED lights up).
4) Push the control 1 to 10 (maximum) and press the RECORD/SHIFT button once.
5) Push the controls 1 to zero and 2 to maximum and press RECORD/SHIFT again
6) Push controls 2 to zero and 3 to maximum and press RECORD/SHIFT again.
7) Repeat these steps up to control 24.
8) Select a memory page (1 to 4) via the PAGE/REC CLEAR button.
9) Save the running light effect in this page by pressing one of the flash buttons in section PRESET B (1 to 12). Use e.g.
button number 1.
10) Leave the programming mode by pressing simultaneously the RECORD/SHIFT and REC EXIT buttons.
PLAYING A RUNNING LIGHT PATTERN
1) Select the mode CHASE/SCENES via the MODE SELECT button. The red LED lights up.
2) Push the control of the appropriate channel (memory) from section PRESET B to the top. In our example it was flash
button 1. This triggers the steps which are stored in that memory. If the appropriate slider control was already in the
upper position, it is necessary to pull it down first and push it up again to trigger the pattern.
ERASING A RUNNING LIGHT PATTERN
1) Activate the programming mode (press RECORD/SHIFT and buttons 1, 5, 6 and 8 –the top row).
2) Select the required page (1 to 4) via the PAGE/REC CLEAR button.
3) Hold the RECORD/SHIFT button down and press quickly TWICE the appropriate flash button from section PRESET B
in which the pattern to be erased is stored.
4) Release the RECORD/SHIFT. All indicator LEDs light up to confirm.
CHANGING A RUNNING LIGHT PATTERN
A running light pattern (scene) can contain up to 99 steps. These steps can be changed or erased later. You can also add
steps later. Each ‘step’ is a determined setting of the variable light intensity (0-100%) of 24 lamps or groups of lamps.
Erasing a particular step:
1) Activate the programming mode (press RECORD/SHIFT and simultaneously 1, 5, 6, and 8).
2) Select the required page via the PAGE button.
3) Press the MODE SELECT button until the red LED lights up (CHASE-SCENES).
4) Hold the EDIT button down and press at the same time the flash button of the appropriate running light pattern (flash
buttons in the lower row of the section PRESET B).
5) Release the EDIT button and select via the STEP button the step to be erased.
6) Press the DELETE button and the selected step will be erased from the memory.
7) Leave the programming mode by holding the RECORD/SHIFT button down while pressing twice the REC/EXIT
button.
Adding steps:
1) Activate the programming mode (press RECORD/SHIFT and simultaneously in sequence 1, 5, 6, and 8).
2) Select the required page via the PAGE button.
3) Press the MODE SELECT button until the red LED lights up (CHASE-SCENES).
4) Hold the EDIT button down and press at the same time the flash button of the appropriate running light pattern (flash
buttons in the lower row of the section PRESET B).
5) Release the EDIT button and select via the STEP button the step just after the step to be added.
6) Set the required light position via the slider controls, press the RECORD/SHIFT button and then the INSERT button.
7) If required, repeat steps 5 and 6 to add more steps.
8) Hold the RECORD/SHIFT button down and press twice the REC/EXIT button to leave the programming mode.
Changing steps:
1) Activate the programming mode (press RECORD/SHIFT and simultaneously in sequence 1, 5, 6, and 8).
2) Select the required page via the PAGE button.
3) Press the MODE SELECT button until the red LED lights up (CHASE-SCENES).
4) Hold the EDIT button down and press at the same time the flash button of the appropriate running light pattern (flash
buttons in the lower row of the section PRESET B).
5) Select the required step via the STEP button.
6) Now you can change the light intensity of the lamps as follows: hold the DOWN button pressed while pressing the flash
button of the channel that you want to change. The display shows which setting has been selected. (0 – 255 is
equivalent to 0 – 100%)
7) Hold the RECORD/SHIFT button down and press twice the REC/EXIT button to leave the programming mode.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BeamZ 154.062 - DMX-024PRO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BeamZ 154.062 - DMX-024PRO in the language / languages: English, German, Dutch, Spanish as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info