765605

BeamZ 154.062 - DMX-024PRO Manual

7
Zoom out
Zoom in
Previous page
1/11
Next page
Connections at the rear panel
On the rear panel are located a number of connectors and a slider control, i.e.: a small connector for the included power
supply (1), a block of 3 DIN connectors for MIDI (2, 3 and 4), a 3-pin DIN connector for the DMX signals (5) featuring a push
switch for polarity inversion (6) an RCA connector for an external audio signal (7) and a 6.3 mm jack for a foot switch (8).
BASIC
FUNCTIONS
FOR
PROGRAMMING
1) Activation of the programming mode:
Keep the RECORD/SHIFT button pushed in and press in sequence the flash buttons 1, 5, 6 and 8. These buttons are
located just below the slider controls in the upper row PRESET A. Release the RECORD/SHIFT button. The red
programming LED should light up.
2) Exit the programming mode:
Hold the RECORD/SHIFT button down and press simultaneously the REC/EXIT button. The red programming LED goes
off.
3) Erasing all programs (be careful !):
Activate the programming mode as described above in step 1. Hold the RECORD/SHIFT button down and press in
sequence the flash buttons 1, 3, 2 and 3 in the section PRESET A. Release the RECORD/SHIFT button. All stored running
light scenes are now erased from the ROM. All LEDs flash to confirm. Press the RECORD/SHIFT and the REC/EXIT
buttons at the same time to leave the programming mode.
4) Erasing the RAM:
The RAM is used as an intermediate memory for a number of running light scenes during the programming process. If you
make a mistake during the programming, you can erase the RAM. Activate the programming mode as described in step 1.
Hold the RECORD/SHIFT button down while pressing the REC/CLEAR button. All LEDs flash once to indicate that the
RAM has been erased.
PROGRAMMING RUNNING LIGHT PATTERNS (SCENES)
1) Activate the programming mode as described in the Basic Functions.
2) Select the mode 1-24 single (the green LED lights up) via the MODE SELECT button. In this mode, you can use all 24
channels.
3) Push the MASTER slider controls A and B to their maximum positions. Note: Control A completely up and control B
completely down.
4) Set the required light position via the slider controls 1 to 24.
5) Press the RECORD/SHIFT button once to store this position in the RAM.
6) Repeat steps 4 and 5 with different positions of the slider controls in order to get an optimal light effect. You can store
up to 99 steps per memory.
7) The programmed steps must now be transferred from the RAM to the ROM. Proceed as follows: Select a memory
page (1 to 4) via the PAGE/REC CLEAR button. Hold the RECORD/SHIFT button down and press one of the flash
buttons 1 to 13 in section PRESET B. You can store up to 99 steps per memory. There are in total 4 pages with 12
memories each.
8) Exit the programming mode (press RECORD/SHIFT and REC EXIT buttons). The red programming LED must go off.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BeamZ 154.062 - DMX-024PRO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BeamZ 154.062 - DMX-024PRO in the language / languages: English, German, Dutch, Spanish as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info