765604

BeamZ 154.060 - DMX-192S Manual

10
Zoom out
Zoom in
Previous page
1/18
Next page
www.beamzlighting.com
1) Activate the programming mode by pressing the PROGRAM key for 2 seconds. The PROG LED is flashing on the
display.
2) Select the running light program via the CHASE keys (1-6) to which you wish to add one or more scenes (steps).
3) Press the TAP SYNC/DISPLAY key once. The STEP LED will light up on the display.
4) Select the step number via the BANK arrow keys behind which you wish to insert a new scene.
5) Program a new scene as described in the section PROGRAMMING OF RUNNING LIGHT SCENES.
6) Press the MIDI/REC (MIDI/ADD) key and the step sequence number on the display increases by 1.
7) Press once again the MIDI/REC (MIDI/ADD) key and the scene will be added.
8) Press the TAP SYNC/DISPLAY key and then the PROGRAM key in order to leave the program mode.
CLEARING A STEP (SCENE)
1) Activate the programming mode by pressing the PROGRAM key until the PROG LED on the display is flashing.
2) Choose the running light program via one of the CHASE keys from which you want to remove a step (scene).
3) Press the TAP SYNC/DISPLAY key once.
4) Use the BANK up/down keys to choose the step number (scene) to be cleared.
5) Press the AUTO/DEL key once. The scene is cleared and the display flashes to confirm.
6) Press the TAP SYNC/DISPLAY and then the PROGRAM key to leave the programming mode.
CLEARING A RUNNING LIGHT PATTERN (CHASE)
1) Keep the desired CHASE key (1-6) pressed and press at the same time the AUTO/DEL key once.
CLEARING ALL RUNNING LIGHT PATTERNS
1) Keep the AUTO/DEL key pressed and switch the power supply off by unplugging the power connector on the rear side.
2) Release the AUTO/DEL key and switch the power supply on again.
PLAYING THE PROGRAMMED SCENES
Manual Operation
1) After having switched on the power supply, always start the DMX operator in the manual mode.
2) Check if the indicator LEDs MUSIC TRIGGER and AUTO TRIGGER on the display are switched off. If necessary,
press the MUSIC/BANK-COPY and AUTO/DEL keys to switch them off.
3) Select the desired memory bank via the BANK arrow keys and press the SCENE keys (2).
Automatic Play
1) This function allows you to play in cycle all scenes that are programmed in a memory bank.
2) Press the AUTO/DEL key to activate the automatic play mode. The AUTO TRIGGER LED on the display must light up.
3) Select the desired memory bank via the BANK arrow keys. The scenes are now played in sequence.
4) The SPEED and FADE controls are used to set the speed and the fading time.
5) During automatic play you can at any time chose another memory bank via the BANK arrow keys.
MUSIC CONTROL
1) Switch the music-control on via the MUSIC/BANK-COPY key. The built-in microphone reacts to the rhythm of the
music.
2) Select the desired memory bank via the BANK arrow keys.
3) Press the MUSIC/BANK-COPY key to switch the music controlled mode off.
USE OF RUNNING LIGHT PATTERNS
MANUAL OPERATION
1) Prior to running light patterns you need to program scenes !
2) This function enables you to play scenes manually in random sequence.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BeamZ 154.060 - DMX-192S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BeamZ 154.060 - DMX-192S in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info