765604

BeamZ 154.060 - DMX-192S Manual

9
Zoom out
Zoom in
Previous page
1/18
Next page
www.beamzlighting.com
5) Select now via the BANK arrow keys the memory bank into which you wish to store the copied scene.
6) Press now the MIDI/REC (MIDI/ADD) key and afterwards the SCENE key containing the number of the scene into
which you wish to store the copied settings.
7) To confirm the copy, the LED’s and the display flash a few times.
8) Switch the program mode off by pressing the PROGRAM key.
CLEARING A SCENE
1) This function allows to reset all 16 DMX channels in a scene.
2) Switch the programming mode on and select via the BANK arrow keys the memory bank that contains the scene to
be removed.
3) Keep the AUTO/DEL key pressed while pushing the relevant scene key.
4) The LED’s flash to confirm and the scene is erased.
CLEARING (RESET) ALL SCENES (CAUTION !)
1) This allows you to erase all programmed scenes at once.
2) Press the PROGRAM key and then the BANK down arrow key. Keep both keys pressed.
3) Switch now the unit off by unplugging the connector of the power supply. Release both keys.
4) Power the unit on again.
DUPLICATION OF A MEMORY BANK
1) This function allows you to transfer at once all 8 programmed scenes from a memory bank into another memory
bank.
2) Switch the programming mode on by pressing the PROGRAM key until the PROG LED is flashing on the display.
3) Select the memory bank you wish to copy via the arrow keys.
4) Press the MIDI/REC (MIDI/ADD) key once.
5) Select now via the arrow keys the number of the memory bank into which you want to copy.
6) Press the MUSIC/BANK-COPY (9) key once. The display flashes to confirm.
7) Switch the programming mode off by pressing the PROGRAM key for 2 seconds. The BLACKOUT mode that is
switched on automatically, can be switched off by the BLACKOUT key.
ERASING A MEMORY BANK
1) This function allows to clear all 8 programmed scenes in a memory bank.
2) Switch the programming mode on by pressing the PROGRAM key until the PROG LED is flashing on the display.
3) Keep the AUTO/DEL pressed while pressing the MUSIC/BANK-COPY key.
4) Release both keys at the same time.
5) The display flashes to confirm.
6) Leave the programming mode by pressing the PROGRAM key for 2 seconds. The BLACKOUT mode that is switched
on automatically, can be switched off by the BLACKOUT key.
PROGRAMMING OF RUNNING LIGHT FUNCTIONS
Attention ! You first need to program scenes into the memory banks before you can use the running light functions.
1) This function allows you to play 240 different scenes in a sequence.
2) Switch the programming mode on by pressing the PROGRAM key until the PROG LED is flashing on the display.
3) Select one of the six running light patterns via the CHASE keys (5).
4) Select the requested scene in one of the memory banks (BANK up/down + SCENE keys).
5) Press the MIDI/REC (MIDI/ADD) key to confirm the selection.
6) You can set up to 240 steps in each of these six running light programs.
7) Repeat the steps 3 to 5 until you have reached the desired effect.
8) Switch the programming mode off by pressing the PROGRAM key for 2 seconds.
CHANGING A RUNNING LIGHT PATTERN
ADDITION OF STEPS
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BeamZ 154.060 - DMX-192S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BeamZ 154.060 - DMX-192S in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info