765604

BeamZ 154.060 - DMX-192S Manual

8
Zoom out
Zoom in
Previous page
1/18
Next page
www.beamzlighting.com
LED DISPLAY
The display shows light green, easy to read symbols that indicate following functions:
1. The first figure indicates the selected running light pattern (CHASE) (1 – 6)
2. The second figure shows which one of the 8 scenes has been selected.
3. The third and fourth figure shows which one of the 30 memory banks is active.
4. In AUTO MODE, a light dot is displayed in the bottom right corner.
5. The MUSIC MODE (music-control) is shown by a dot on the top right side of the display.
6. The BLACKOUT MODE is indicated by a flashing dot in the upper left corner.
7. In programming mode, a flashing dot appears on the bottom left side of the display.
PROGRAMMING OF THE VARIOUS FUNCTIONS
Programming of the running light scenes
1. Make sure that all units to be controlled, are connected and set to the correct DMX start addresses.
2. Keep the program key (6) more than 2 seconds pressed to activate the programming mode. The green dot in the left
bottom corner should flash and continue to flash during the programming process.
3. Select the required unit via one of the SCANNER keys. Up to 16 channels per unit are available, 1 to 8 on page A and
9 to 16 on page B. Press the PAGE SELECT key until the LED next to the row 1 to 8 (PAGE A) lights up.
4. Set the desired light intensity, position of the mirror, colour or gobo via the slider controls. If required, press PAGE
SELECT to program a second set of 8 settings if the connected unit offers more than 8 channels.
5. To store these settings, press the MIDI/ADD or MIDI/REC key.
6. Select now with the BANK arrow keys (4) the requested memory bank where you want to store this scene. N.B. The
unit features a memory of 30 banks of which each can contain 8 scenes.
7. Press now one of the scene keys (2) and the settings will be stored. You can control this on the display. The second
figure indicates the scene number and the last two figures show the number of the selected memory bank. To confirm
the setting, the LED’s and the display flash a few times.
8. HINT: Please note the scene and bank numbers. It is difficult to search when all 240 memory locations are occupied.
9. Repeat steps 3 to 7 to program other scenes. N.B.! Switch the already programmed units off via the SCANNER keys
(1) otherwise the settings will be transferred.
10. To leave the programming mode, press the PROGRAM key until the flashing dot disappears. After the programming
mode, the unit switches automatically into BLACKOUT mode. Press the BLACKOUT key to switch this mode off.
CHANGE OF ALREADY PROGRAMMED SCENES
1) This function allows you to change already set scenes.
2) Press the PROGRAM key as described above.
3) Select the requested bank number via the BANK arrow keys (use your notes !).
4) Select now the requested scene via the correct scene key.
5) Make the new settings via the slider controls.
6) Press the MIDI/REC (or MIDI/ADD) key and then the scene key (see point 4) to store the new settings.
7) Attention! Select the correct scene key otherwise you will overwrite by mistake the settings of a scene that you did
NOT want to change.
COPYING OF SETTINGS
1) This function allows to copy settings from one unit to another unit. This features is easy and time saving especially for
the programming of running lights.
2) Press the SCANNER key of the unit from which you want to copy the settings and press at the same time the key
from the unit into which you want to copy the settings. Release both keys. The settings have been transferred.
COPYING SCENES
1) This function allows you to copy the settings from an already programmed scene to a new scene.
2) Switch the programming mode on by pressing the PROGRAM key until the green dot in the bottom left corner is
flashing.
3) Select the required memory bank via the BANK arrow keys which contains the scene that you wish to copy.
4) Press the correct scene key.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BeamZ 154.060 - DMX-192S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BeamZ 154.060 - DMX-192S in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info