758289

Batavia BT-JS002 - 7063410 Manual

11
Zoom out
Zoom in
Previous page
1/42
Next page
9
English
16.2 Secure the parallel stop by tightening
the fastening screws (11) in the desired
position.
When not using the parallel stop, tighten
the fastening screws (11) securely. The
screws can be unscrewed and fall off
due to the vibration of sawing.
17. Laser
17.1 Safety instructions for the laser cut-
ting guide
a. Do not point the laser beam at persons
or animals and do not look into the
laser beam. This laser emits a laser
beam that falls under laser class 2 in
accordance with EN 60825-1:2014. You
could blind people with it.
b. A laser is not a toy and does not
belong in the hands of children. Using
it incorrectly may result in irreparable
damage to the eyes.
c. It is forbidden to manipulate the laser
so as to increase its power in any way.
No liability will be assumed for any
damages caused as the result of fail-
ure to comply with these safety
instructions.
d. The laser does not contain any ser-
viceable parts. Therefore, do not open
the housing. Otherwise, you will ren-
der the warranty void.
e. Warning! Do not swap the laser with
another type of laser. Only the manu-
facturer of the laser or an authorised
representative may perform repairs.
f. Do not point the laser beam towards
highly reflective surfaces.
g. Do not insert any hard objects in the
laser optics.
h. Clean the laser optics with a soft, dry
cloth.
18. Using the laser
The beam line of the laser is available to
assist in making straight cuts. You can
either cut along the projected line or point
the laser beam at a xed point on the work
piece and then cut.
18.1 To switch the laser on, push the On/Off
switch (13) for the laser.
18.2 To switch the laser off, push the On/Off
switch (13) for the laser again.
19. Tips for cutting
• Clamp the workpiece. Use a clamping
device for small workpieces.
• Draw a line to dene the direction in
which to guide the saw blade.
• Firmly hold the machine by the grip.
• Set the sawing speed.
• Set the mitre angle.
• Set the pendulum position.
• Switch on the machine.
• Wait until the machine has reached full
speed.
• Place the saw shoe on the workpiece.
• Slowly move the machine along the
pre-drawn line, rmly pressing the saw
shoe against the workpiece.
• Do not apply too much pressure on the
machine. Let the machine do the work.
• Switch off the machine and wait for the
machine to come to a complete stand-
still before putting the machine down.
20. Cleaning and maintenance
• To avoid injury always pull the power
plug before maintaining or cleaning the
machine.
• Clean the machine with a moist cloth.
• If the machine is very dirty use a mild
detergent or soap on the cloth. Other
cleaning agents may contain chemical
substances which may damage the
plastic parts of the machine.
• Do not allow liquids to enter the
machine and do not immerse the
machine in liquids of any kind.
• Repairs, inspections of the interior of
the machine, adjustments and replace-
ment of the carbon brushes may only
be undertaken by a professional. Only
identical replacement parts may be
used! For further information please
contact our customer service
department.
• Always keep the ventilation slots (5)
open and clean. After each use remove
dirt and contaminations with a brush or
blow it out with compressed air.
7062849-Jig_Saw_800W-Ma-1803-09.indb 9 22-03-18 11:07
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Batavia BT-JS002 - 7063410 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Batavia BT-JS002 - 7063410 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info