Manual Batavia BT-CSN001 - 7063094 (page 8 of 32) (English, German, Dutch, French)

758256

Zoom out

Zoom in

1/32

English

7.2 Press in the magazine catch  and

pull back the magazine casing .

7.3 Fill the magazine with suitable nails or

staples.

7.4 Check that the nails or staples are cor-

rectly placed in the magazine.

7.5 Slide the magazine casting to close it

and check that it clicks in place.

7.6 Place the battery.

8. Operation

8.1 Prior to operation, make sure the bat-

tery pack is fully charged.

8.2 Check whether the nails or staples are

placed in the magazine correctly.

8.3 Hold the handle rmly with magazine

at on the work surface at a 90 degree

angle.

8.4 The brad nailer has two ring modes:

Single and Contact Firing.

 

– Push the Firing Mode switch  to the

left.

– Depress the safety contact pin 

against the work surface.

– Squeeze the trigger  to re the staple

or nail. Release the trigger and safety

contact pin after ring.

 

– Push the Firing Mode switch  to the

right.

– Squeeze the trigger .

– Press the safety contact pin 

against the work surface to re a nail or

staple.

– With the trigger still depressed, raise

the device and press it against the next

area you want to re a nail or staple

into.

– When the contact pin is pressed against

the work surface the device will re.

Do not keep the trigger

depressed when the brad nailer is not in

use.

9. Adjusting the nailing depth

To assure that each nail penetrates to the

same depth, be sure that the nailer is always

held rmly against the workpiece. If nails

are driven too deep or shallow into the work-

piece, adjust the nailing in the following

order.

9.1 Remove the battery  from the nailer.

9.2 If nails are driven too deep, turn the

adjuster  to the shallow side. (See

) Adjustments are in half-turn

increments. If nails are driven too shal-

low, turn the adjuster to the deep side.

9.3 Stop turning the adjuster when a suita-

ble position is reached for a nailing test.

9.4 Connect the battery to the Nailer. Per-

form a nailing test.

10. Removing a jammed nail or

staple

You must remove any jammed nail/staple

before using the tool any further. Otherwise,

it could cause damage to the mechanism.

a. Remove the battery pack from the

tool.

b. Open the magazine  and remove the

nails or staples in the channel.

c. Clear the jammed staple or nail.

d. If the nail or staple remains jammed

after following the above instructions,

slightly loosen the hex screws on the

nose-piece with a hex wrench. Then

remove the jammed pieces manually.

Pliers can be used if necessary.

e. Securely re-tighten the hex screws in

the nose piece after the jammed nail

has been successfully removed.

f. Reload the staples or nails, close the

magazine and insert it back into the

nailer.

11. Work light

When the trigger switch  is pressed the

work light  turns on. When the trigger

switch is released the work light turns off

after approximately ve seconds.

12. LED Status indicator

• Flashing red LED: Nail/Staple jam.

• Solid red LED: Low battery.

• Flashing green LED: Overheat.

• Solid green LED: Out of Nails.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Batavia BT-CSN001 - 7063094 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,24 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Batavia BT-CSN001 - 7063094 Manual

Product: