Manual Batavia BT-CS009 - 7062244 (page 31 of 66) (English, German, Dutch, French)

759583

Zoom out

Zoom in

1/66

English

tool and inspect the workpiece. Move

forward at a slower speed.

Line cuts

You can follow a drawn line with the help of the

indicator marks (a), at the front and rear of the

safety guard. For precise work, the relationship

between the saw cut and a marked indicator

line must be established using a test piece.

The ideal positioning of the saw cuts must then

be achieved by adjusting the indicator line to

the target line.

Working with large workpieces

When working with large workpieces or cutting

straight edges:

• Use fastening clamps to tighten a board or

border onto the workpiece as an auxiliary

stop.

• Guide the left-hand side of the base plate

along the auxiliary stop.

Plunge cuts (Figure 1)

Note: Some very hard materials are not suita-

ble for plunge cuts.

1. Put the base plate on the workpiece.

Make sure that the rear lateral depth mark-

ing is at the height of the beginning of the

cut.

2. Switch on the electric power tool and

allow a couple of seconds to pass until the

tool insert reaches its full speed. Then

plunge the tool insert, slowly but with

some pressure.

3. Push the electric power tool forwards

through the workpiece.

4. When you reach the end of the cut, switch

off the electric power tool and pull it out of

the workpiece.

Cutting tiles

Adhesive tape or insulation tape on the work-

piece makes the work easier and helps to

prevent it from getting scratched.

After use:

1. Switch of the tool

2. Remove the plug from the socket

3. Let the tool cool down

4. Remove all accessories such as

sawblades

CLEANING AND MAINTENANCE

Warning! Pull out the power plug

before any cleaning work.

Cleaning

• Keep safety devices, ventilation openings

and the motor housing as free as possible

from dirt and dust. Rub the electric power

tool with a clean cloth or blow over it with

low pressure compressed air.

• We recommend that you clean your elec-

tric power tool immediately after each use.

• Clean the electric power tool regularly with

a damp cloth and somewhat soft soap. Do

not use any cleaning or solvent materials;

these can attack the device’s plastic com-

ponents. Make sure that no water can get

inside the electric power tool.

• Unlock and remove the lid if the adapter is

dusty. Replace the lid after cleaning.

Maintenance

Carbon brushes

In the event of excessive sparking, allow a

qualied person to examine the carbon

brushes.

ATTENTION! The carbon brushes

may only be exchanged by a qualied

person.

There are no inner parts of the tool which need

maintenance.

REPAIR AND ORDERING OF SPARE

PARTS

Exchanging the power cable

If the power cable of this electric power tool is

damaged, it must be replaced by the manufac-

turer, its customer services department or a

similarly qualied person to avoid danger.

Spare parts/Accessories

Spare parts can be ordered through the Cus-

tomer Service using the following information:

• Type of device

• Model of the unit

• ID number of the device

Transport

• Do not lift the tool by the mains cable

• Transport the tool in its original packaging

to avoid transport damage

7062244_MaxxSaw_Ma_#1612-19.indb 29 19-12-16 10:31

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Batavia BT-CS009 - 7062244 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 5,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Batavia BT-CS009 - 7062244 Manual

Product: