759583

Batavia BT-CS009 - 7062244 Manual

30
Zoom out
Zoom in
Previous page
1/66
Next page
English
28
.
• Always hold the electric power tool with a
rm grip.
• Exert no force! Push the electric power
tool forwards, gently and evenly.
• The electric power tool must not be
braked with the hand or by applying lateral
pressure.
• The safety guard may not be blocked and
must be returned to the starting position
after the nal working step.
• Before use of the electric power tool,
inspect the function of the safety guard
with the tool unplugged from the mains.
• Before each use of the electric power tool,
make sure that the safety mechanisms
such as the safety guard, anges and
adjustment devices are functioning and/or
are correctly installed and fastened.
• A suitable dust extraction system is to be
connected to the dust extraction connec-
tion (10). Make sure that the dust extrac-
tion is correctly and securely attached.
Switching on and off (Figure1)
Switching on:
Push the safety switch (1b) forward with one
nger and then press the On/Off switch (1a)
keeping it pressed.
Switching off:
Let go of the On/Off switch (1a).
Using the laser (Figure 7)
Using the laser beam-guide makes sawing in a
straight line much easier.
a. Either along a drawn line
b. Or by aligning the beam to a marked
point
• To switch the laser (9) on, press the Laser
On/Off switch (11)
• To switch the laser (9) off, press the Laser
On/Off switch (11) again
Overload protection (Figure 1)
The electric power tool is equipped with an
overload protection. The overload indicator (15)
displays the operating condition of the electric
power tool.
Overload indicator (15) ashing: The electric
power tool is approaching the limiting load
– reduce the forward feed speed.
Overload indicator (15) continually lit: The elec-
tric power tool is overloaded or jammed
– the electric power tool cuts out. In this event,
switch the electric power tool off and allow it to
cool down before using it again.
Use
WARNING! Always begin by making
a test cut in a left-over piece.
1. Firmly clamp small wooden pieces before
commencing work. Never hold them in
your hand.
2. Fully observe the safety regulations! Wear
safety glasses!
3. Adjust the cutting depth and rotation
speed.
4. Pick up the electric power tool and make
sure that none of the ventilation openings
are covered.
5. Switch on the electric power tool and wait
for several seconds until the tool insert has
attained its full rotation speed.
6. The waste piece should be on the right or
left side of the electric power tool, so that
the wide part of the supporting table rests
on its entire surface.
7. The base plate must always rest at on the
workpiece.
8. Place the base plate to the marked area
(6) onto the workpiece
9. Press the release button (12) and slowly
push the tool insert (17) into the workpiece
or, if necessary, plunge it.
10. Push the electric power tool forwards
through the workpiece. Never move it
backwards!
11. Apply only a gentle force to the electric
power tool when working.
12. If sawing along a marked line, lead the
electric power tool along the appropriate
groove.
13. If the overload indicator (15) ashes,
reduce your speed.
14. If the electric power tool stops and the
overload indicator (15) is lit continuously,
then the overload protection of the electric
power tool has responded. Reason: You
were moving forward too quickly or have
encountered an obstacle in the workpiece.
In this case, switch off the electric power
7062244_MaxxSaw_Ma_#1612-19.indb 28 19-12-16 10:31
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Batavia BT-CS009 - 7062244 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Batavia BT-CS009 - 7062244 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 5,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info