Manual Barbecook Spring 2002 (page 15 of 308) (All languages)

790883

Zoom out

Zoom in

1/308

14 TROUBLESHOOTING

Problem Probable cause(s) Solution(s)

•Gas supply not open

•Venturis not placed over openings of gas valves

•Burner openings blocked

•Gas cylinder (almost) empty

•Pressure regulator not connected correctly to

cylinder and/or hose

Some heat diffe ences are norrnal, see “1.7 Making

optima! use of the heat” and “10.6 Taking advantage

of the heat zones”. Probable cause(s) for big heat

diffe ences:

•Appliance not preheated

•Food too fatty

•Fat drain hole blocked, fat in bowl and/or fat on

burners

•Temperature too high

•Burners or venturis blocked

•Salt on burners

•Appliance connected to butane

•Burner blocked, pierced or rusted

•Burners or venturis blocked

•Lots of wind

•Gas cylinder (almost) empty

•Fat in bowl or on burners

•Hot weather

•New (full) gas cylinder

•Gas injector, venturi and/or burner dirty

•Burner or venturi blocked

•No gas supply

•No battery installed or battery not installed

correctly

•Middle burner not lit firs

•lgniter wiring not mounted correctly

•Electrode damaged

•Faulty ground

•Faulty igniter

•No battery installed or battery not installed

correctly

•Empty battery

•lgniter button not assembled correctly

•Faulty spark generator

•Faulty ground

•Low battery

•Wet or broken electrodes

•Faulty wiring

•Faulty ground

•Burner and electrode too far apart

Not enough heat

Heat not distributed evenly over

grill surface

Excessive heat and/or fla e-ups

Yellow ﬂames

Flash-backs (ﬂames outside

venturis/at control knobs)

Flames higher than edge of

bowl

Pressure regulator hums

Burner whistles when set to

LOW

Impossible to light burner

(using either igniter or match)

lmpossible to light burner with

igniter

No sparks nor sound when

pressing igniter

Sparks present, but not on all

electrodes and/or not powerful

enough

Sparks present that do not

originate from burners

Only sound (no sparks) when

pressing igniter

Incomplete ﬂame

•Open gas supply

•Place venturis over openings of gas valves

•Clean burner openings or replace burners

•Replace gas cylinder

•Reconnect pressure regulator to cylinder and/

or hose

•Preheat appliance

•Trim excess fat or set burners to a low position

•Clean fat drain hole, bowl and burners

•Set burners to a lower temperature and/or grill

food indirectly

•Clean burners and venturis

•Clean burners

•Connect appliance to propane, using an

appropriate pressure regulator

•Clean or replace burner

•Close gas supply and set burners to OFF.

•Let appliance cool down.

•Clean burners and venturis.

•Put appliance with rear side towards wind

•Replace gas cylinder

•Clean bowl or burners

•Not a hazard or defect. Should stop

automatically after a while.

•Clean gas injector, venturi and burner

•Clean burner and venturi

•Open gas supply and press safety knob on

pressure regulator (not present on all regulators)

•(Re)install battery, with terminals positioned

correctly

•Light the middle burner firs

•Check and re-assemble all igniter connections

•Replace electrode

•Check and re-assemble electrodes, burners

and igniter

•Replace igniter

•(Re)install battery, with terminals positioned

correctly

•Replace battery

•Re-assemble igniter button

•Replace spark generator

•Reconnect spark generator and electrodes

•Replace battery

•Dry electrodes with paper towels or replace

electrodes

•Replace wiring

•Reconnect spark generator and electrodes

•Slightly bend electrode to bring it closer to the

burner

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Barbecook Spring 2002 in the language / languages: All languages as an attachment in your email.

The manual is 24.75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Barbecook Spring 2002 Manual

Product: