22653
13
Zoom out
Zoom in
Previous page
1/20
Next page
Press and hold the touch eld for more than three
seconds on the loudspeaker you wish to calibrate
(while you are pressing, the indicator light quickly
ashes red).
If you wish to cancel an ongoing calibration, press
the touch eld again – or press BACK on the Beo4
remote control.
For an overview of the indicator lights, refer to
page 17.
The moving microphone is used during the
calibration. Make sure that there is always free
space in front of the microphone.
To calibrate BeoLab5
Perform the calibration for each loudspeaker
in your setup separately. The calibration takes
a couple of minutes for each loudspeaker. You
cannot start the calibration if the loudspeaker
has been locked by the PIN code system*.
> Make sure that the loudspeaker is in standby.
Ifnecessary, switch the loudspeaker to standby
as explained in the chapter ‘Daily use’ (pp. 4–5).
> Press and hold the touch eld for more than
three seconds, then let go of the panel.
When the calibration begins, the indicator light
ashes green.
Once started, and during the calibration, the
following occurs:
The microphone extends a little, and the speaker
generates a series of sound signals, starting with
very low bass tones.
After a while the microphone extends a little
further, and the sound signals begin again.
When the calibration is complete, the
microphone retracts and the loudspeaker
switches to standby. The indicator light shines
red for a while. You may now proceed with the
next loudspeaker.
If the indicator light ashes red, an error has
occurred during the calibration. To solve this, do
the following:
> Press and hold the touch eld for more than one
second, then let go of the eld.
The loudspeaker will switch to standby, and the
indicator light shines red for a while
> Check for any source of noise which may have
interferred with the calibration, and wait until
the noise has stopped.
> Press and hold the touch eld for more than
three seconds to start the calibration again.
*NOTE! If the loudspeaker is locked by the PIN code
system, the indicator light shines intermittently red
and green when you switch on. Unlock the
loudspeaker as explained in Use the PIN code
system (p. 14).
13
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bang Olufsen Beolab5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bang Olufsen Beolab5 in the language / languages: English as an attachment in your email.

The manual is 0,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bang Olufsen Beolab5

Bang Olufsen Beolab5 User Manual - German - 20 pages

Bang Olufsen Beolab5 User Manual - Dutch - 20 pages

Bang Olufsen Beolab5 User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info