658689
27
Zoom out
Zoom in
Previous page
1/52
Next page
| 25
Software setup | Zeus Glass Helm Installation Manual
bearing alignment setting, so that the heading marker and land mass intersect.
Adjust antenna height
Set the radar scanner height relative to the water surface. The Radar uses this value to
calculate the correct STC settings.
Adjust local interference reject
Interference from some onboard sources can interfere with the Broadband radar. One
symptom of this could be a large target on the screen that remains in the same relative
bearing even if the vessel changes direction. Choose from Local interference rejection LOW,
MED or HIGH. Default is LOW
Sidelobe suppression
Occasionally false target returns can occur adjacent to strong target returns such as large
ships or container ports. This occurs because not all of the transmitted radar energy can be
focused into a single beam by the radar antenna, a small amount energy is transmitted in
other directions. This energy is referred to as sidelobe energy and occurs in all radar systems.
The returns caused by sidelobes tend to appear as arcs.
Note: This control should only be adjusted by experienced radar users. Target loss in harbour
environments may occur if this control is not adjusted correctly.
When the radar is mounted where there are metallic objects near the radar, sidelobe energy
increases because the beam focus is degraded. The increased sidelobe returns can be
eliminated using the Sidelobe Suppression control in the Radar installation menu.
By default this control is set to Auto and normally should not need to be adjusted. However
if there is signi cant metallic clutter around the radar, sidelobe suppression may need to be
increased. The control should be adjusted as follows:
Set Radar range to between 1/2 nm to 1 nm and Sidelobe Suppression to Auto.
Take the vessel to a location where sidelobe returns are likely to be seen. Typically this would
be near a large ship, container port, or metal bridge
Traverse the area until the strongest sidelobe returns are seen.
Change Auto sidelobe suppression to OFF then select and adjust the sidelobe suppression
control until the sidelobe returns are just eliminated. You may need to monitor 5-10 radar
sweeps to be sure they have been eliminated.
Traverse the area again and readjust if sidelobes returns still occur.
Exit the installation menu.
Restore radar to Factory Default
This can be used to revert all user adjustments.
Video In con guration
Press the menu key when on the video page or panel to open the setup
dialogue.
Enable PAL or NTSC depending on the video ouput standard of the
selected camera.
You can optimize the video display by adjusting the video image
settings (brightness, saturation, etc.). The settings are applied individually
for each video source.
Mirror image may be applied where the camera is providing a rear view,
and the user wishes to see objects as they would appear in a vehicle
rearview mirror, ie, on the same side as they actually are.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BandG Zeus2 Glass Helm at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BandG Zeus2 Glass Helm in the language / languages: English as an attachment in your email.

The manual is 6,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of BandG Zeus2 Glass Helm

BandG Zeus2 Glass Helm User Manual - English - 136 pages

BandG Zeus2 Glass Helm User Manual - German - 115 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info