784764
27
Zoom out
Zoom in
Previous page
1/35
Next page
General Messages
Several alerts and messages may be
displayed in a sequence.
Possible freezing condition
A potential freeze condition has been detected, or the
AuxFreezeSwitchhasclosed.Allwaterdevicesare
activated. In some cases, pumps may turn on and off
and the heater may operate during Freeze Protection.
This is an operational message, not an error indication.
The water is too hot – M029*
The system has detected a spa water temp of 110°F
(about 43°C) or more, and spa functions are disabled.
System will auto reset when the spa water temp is
below108°F(about42°C).Checkforextendedpump
operation or high ambient temp.
The water level is too low
This message can only appear on a system that uses a
water level sensor. It appears whenever the water level
get too low (or the water level sensor is disconnected),
and automatically disappears when the water level is
adequate. Pumps and the heater turn OFF when this
message appears.
Heater-Related Messages
The water ow is low – M016**
Theremaynotbeenoughwaterowthroughthe
heater to carry the heat away from the heating
element. Heater start up will begin again after about 1
minute. See “Flow Related Checks” below.
The water ow has failed* – M017**
Thereisnotenoughwaterowthroughtheheaterto
carry the heat away from the heating element and the
heater has been disabled. See “Flow Related Checks”
below. After the problem has been resolved, reset
themessage*.
The heater may be dry* – M028**
Possible dry heater, or not enough water in the heater
to start it. The spa is shut down for 15 minute. Reset
thismessage*toresettheheaterstart-up.See“Flow
Related Checks” below.
The heater is dry* – M027**
There is not enough water in the heater to start it. The
spa is shut down. After the problem has been resolved,
youmustresetthemessage*torestartheaterstartup.
See “Flow Related Checks” below.
The heater is too hot* – M030**
One of the water temp sensors has detected 118°F
(about 48°C) in the heater and the spa is shut down.
Youmustresetthemessage*whenwaterisbelow
108°F (about 42°C). See “Flow Related Checks” below.
Flow-related checks
Checkforlowwaterlevel,suctionowrestrictions,
closed valves, trapped air, too many closed jets and
pump prime. On some systems, even when spa is
shut down by an error condition, some equipment
may occasionally turn on to continue monitoring
temperature or if freeze protection is needed.
spaTouch 3 User Guide
42344_Rev D 27
MESSAGES
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Balboa SpaTouch3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Balboa SpaTouch3 in the language / languages: English as an attachment in your email.

The manual is 10.53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info