784764
26
Zoom out
Zoom in
Previous page
1/35
Next page
Follow these steps to
prepare you spa.
Preparation & Filling
Fill the spa to its correct operating level. Be sure to
open all valves and jets in the plumbing system before
llingtoallowasmuchairaspossibletoescapefrom
theplumbingandthecontrolsystemduringthelling
process. After turning the power on at the main power
panel, the top-side panel will display a splash screen or
startup screen.
Priming Mode – M019*
After the initial start-up sequence, the control will enter
Priming Mode and display a Priming Mode screen.
Only pump icons appear on the priming mode screen.
During the priming mode, the heater is disabled to
allow the priming process to be completed without the
possibilityofenergizingtheheaterunderlow-owor
no-owconditions.Nothingcomesonautomatically,
but the pump(s) can be energized by selecting the
“Jet”buttons.IfthespahasaCircPump,itcanbe
turned on and off by pressing the “Circ” button during
Priming Mode.
Priming the Pumps
As soon as the Priming Mode screen appears on the
panel,selectthe“Jets1”buttononcetostartPump1
in low-speed and then again to switch to high-speed.
Also, select the other pumps, to turn them on. The
pumps should be running in high-speed to facilitate
priming. If the pumps have not primed after 2 minutes,
andwaterisnotowingfromthejetsinthespa,donot
allow the pumps to continue to run. Turn off the pumps
and repeat the process. Note: Turning the power off
and back on again will initiate a new pump priming
session. Sometimes momentarily turning the pump
off and on will help it to prime. Do not do this more
than 5 times. If the pump(s) will not prime, shut off
the power to the spa and call for service. Important: A
pump should not be allowed to run without priming for
more than 2 minutes. Under NO circumstances should
a pump be allowed to run without priming beyond
the end of the 4 minute priming mode. Doing so may
cause damage to the pump and cause the system to
energize the heater and go into an overheat condition.
Exiting Priming Mode
The system will automatically enter the normal heating
andlteringattheendoftheprimingmode,which
lasts4minutes.YoucanmanuallyexitPrimingMode
by pressing the “Back” button on the Priming Mode
Screen.Notethatifyoudonotmanuallyexitthe
priming mode as described above, the priming mode
will be automatically terminated after 4 minutes.
Be sure that the pump(s) have been primed by this
time.OncethesystemhasexitedPrimingMode,the
top-side panel will display the Main Screen, but the
display will not show the water temperature yet. This is
becausethesystemrequiresapproximately1minute
ofwaterowingthroughtheheatertodeterminethe
water temperature and display it.
*M0XX is a Message Code.
spaTouch 3 User Guide
42344_Rev D 26
FILL IT UP!
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Balboa SpaTouch3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Balboa SpaTouch3 in the language / languages: English as an attachment in your email.

The manual is 10.53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info