496278
7
Zoom out
Zoom in
Previous page
1/34
Next page
BABYPHONE HIGH CARE Instruction Manual
12
B / Receiver
1. Operation from battery pack
The Li polymer battery pack is already installed in
the unit.
2. Recharging and operation on the base
Before using the receiver for the first time, make
sure it is turned off and recharge it on its base. The
charge indicator will show a red light. Once the
battery is fully charged (average time 3 hours) the
indicator will turn green. The receiver is then ready
to be turned on and used. If you decide to leave the
receiver on its base, when it detects that the charge
level is too low the base will automatically start
recharging the battery.
N.B.: TO ENSURE MAXIMUM LIFE FOR YOUR
BATTERY, WAIT UNTIL IT IS COMPLETELY
DISCHARGED BEFORE RECHARGING IT.
CONTROLS LAYOUT
Receiver
8. Power ON/OFF and vibration switch
9. Up/Down button
10. Mode button
11. LED sound level meter
12. Speaker
13. Charging contacts
Transmitter
1. Power ON/OFF and night light switch
2. Up/Down button
3. Mode button
4. Night light
5. Microphone
6. Power on indicator
7a. DC jack
7b. Temperature sensor
Charger
14. Charging indicator
15. Charging pins
16. DC jack
Channel NO./
Baby’s Room Temperature
Lower Temperature Limit
Upper Temperature Limit
Battery Status Indicator
Transmitter Battery Low Icon
Vibration Icon
Out-of-range Icon
Digital Code
Speaker Volume Bar Graph
Receiver LCD Screen
2. Operation using the (AC adapter supplied)
The transmitter can be operated on AC mains using
the supplied 6V AC adapter. Connect the output
plug of adapter to DC jack (7a) of the transmitter.
Connect the adapter to the mains. The power
supply from the battery will be cut off once the
receiver is mains-operating.
N.B.: The communication range is longest when the
transmitter is operated on AC mains.
1
2
13
BABYPHONE HIGH CARE Instruction Manual
SETTINGS
Channel NO./
Baby’s Room Temperature
Range Check Icon
Transmit Icon
Night Light VOX Icon
Night Light Icon
Battery Status Indicator
Digital Code
Microphone Sensitivity Bar Graph
Transmitter LCD Screen
TRANSMITTOR RECEIVER
Channel and
digital code
setting
Output power
setting
Press and hold the mode button (3) for
more than 5 seconds ; a beep will sound
once the unit goes into programming
mode. The LCD will show following:
Press and hold the mode button (10) for
more than 5 seconds ; a beep will sound
once the unit goes into programming
mode. The LCD will show following:
Use selection button (2) to chose the
channel and press the mode button (3) to
validate your choice. The LCD will show
following (here CH 2 is selected):
Use selection button (9) to select the same
channel as on the transmitter and press
the mode button (10) to validate your
choice. The LCD will show following (here
CH 2 is s elected):
Use selection button (2) to chose the digital
code and press the mode button (3) to
validate your choice. The LCD will show
following (here digital code 28 is selected):
Use selection button (9) to select the same
digital c ode as o n the transmitter and press
the m ode b utton (10) to validate your choice.
The LCD will show following (digital code
28 is selected):
Use selection button (2) to chose the
output power output. Hi means high
power while Lo means low p ower and ELo
means extra low power. Press the mode
button (3) to validate your choice.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Babymoov High Care at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Babymoov High Care in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info