661364
295
Zoom out
Zoom in
Previous page
1/316
Next page
APPENDIX
293
7
The embroidery
pattern is misaligned.
The carriage moved while removing
embroidery frame.
The pattern may become misaligned if
the presser foot was hit or the carriage
was moved while replacing bobbin
thread, changing needle, or working
near embroidery frame.
Be careful when removing and
reattaching the embroidery frame while
replacing bobbin thread, changing
needle, or working near embroidery
frame.
If the carriage is moved, turn the
machine off, then on again. The correct
frame position at the time that the
machine was stopped is stored in the
machine’s memory, and the
embroidery frame is returned to the
correct position.
The design was not digitized correctly.
The design may need more pull
compensation or underlay to
accommodate stretchy or high-napped
fabrics.
The size of the
installed embroidery
frame is not correctly
detected.
The thumbscrews on the embroidery
frame holder are loose.
Use the included disc-shaped
screwdriver to firmly tighten the
thumbscrews.
p.30
The starting position
for the embroidery
frame is horizontally
misaligned.
The thumbscrews on the embroidery
frame holder are loose.
Use the included disc-shaped
screwdriver to firmly tighten the
thumbscrews.
p.30
There are loops in the
upper thread.
The upper thread tension is low.
After passing the upper thread through
the hole in the presser foot, pull the
thread by hand to check the thread
tension. If it is difficult to determine,
compare it with other needle bars
where looping does not occur.
p.125
The thread tension does not correspond
to the amount that the thread tension
knob was tightened.
If the thread tension cannot be
adjusted, thread wax and dust may
have collected in the upper or middle
thread guide plates, causing the thread
tension guide plates to rise. Clean the
thread tension guide plates.
p.284
Thread is not correctly threaded around
upper thread tension discs.
Clean upper thread tension disc.
Rethread and make sure tension disc
rotates when pulling on thread.
p.284
The thread quality is poor.
Try sewing with different thread. If the
problem no longer occurs after the
thread is changed, the thread quality is
the problem. Replace the thread with
one of good quality.
The machine is noisy.
Lint may be wound in the hook. Clean the hook. p.281
The upper thread is not threaded
correctly.
Check the thread path, and then thread
the upper thread again.
p.57
The hook is damaged.
Replace the hook.
Consult your nearest authorized Baby
Lock retailer.
Not enough oil was applied. Oil recommended parts. p.285
Symptom Probable Cause Remedy Reference Page
295


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Valiant - BMV10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Valiant - BMV10 in the language / languages: English as an attachment in your email.

The manual is 15,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Valiant - BMV10

Baby Lock Valiant - BMV10 Additional guide - English - 1 pages

Baby Lock Valiant - BMV10 Additional guide - English, French, Spanish - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info