525694
205
Zoom out
Zoom in
Previous page
1/216
Next page
TROUBLESHOOTING
Maintenance and Troubleshooting
Appendix A-15
A
1
Skipped stitches Needle is turned, bent or the point is dull. Replace the needle. B-51
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle
Combination” chart.
B-53
Machine is threaded incorrectly. Check the steps for threading the machine
and rethread it correctly.
B-42
Dust or lint has collected under the needle
plate.
Remove the dust or lint with the brush. A-3
Needle is installed incorrectly. Reinstall the needle correctly. B-51
Needle is defective. Replace the needle. B-51
Thin or stretch fabrics are being sewn. Sew with one sheet of thin paper under the
fabric.
S-9
Needle breaks Needle is installed incorrectly. Reinstall the needle correctly. B-51
Needle clamp screw is not tightened. Tighten the needle clamp screw. B-52
Needle is turned or bent. Replace the needle. B-51
Using improper needle or thread for the
selected fabric.
Check the needle and fabric combination. B-53
Wrong presser foot was used. Use the recommended presser foot.
S-68
Upper thread tension is too strong. Adjust the thread tension setting. S-12
Fabric is pulled during sewing. Do not pull the fabric during sewing.
Spool cap is set incorrectly. Check the method for attaching the spool
cap, then reattach the spool cap.
B-42
There are scratches around the holes in the
needle plate.
Replace the needle plate, or consult your
authorized retailer.
A-3
There are scratches around the hole(s) in the
presser foot.
Replace the presser foot, or consult your
authorized retailer.
B-49
There are scratches on the bobbin case. Replace the bobbin case, or consult your
authorized retailer.
A-3
Needle is defective. Replace the needle. B-51
Upper threading is incorrect. Check the steps for threading the machine
and rethread the machine.
B-42
Bobbin is set incorrectly. Reset the bobbin thread correctly. B-39
Presser foot is attached incorrectly. Attach the presser foot correctly. B-49
Screw of the presser foot holder is loose. Securely tighten the screw of the presser
foot.
B-49
Fabric is too thick. Use fabric that the needle can pierce when
the handwheel is turned.
S-7
Fabric is fed forcefully when sewing thick fabric
or thick seams.
Allow the fabric to be fed without being
forcefully pushed.
Stitch length is too short. Adjust the stitch length. S-10
Bobbin thread is incorrectly wound. Use a correctly wound bobbin. B-34
Fabric does not feed
through the machine
Feed dogs are set in the down position.
Press , and then turn the handwheel to
raise the feed dogs.
S-40
Stitches are too close together. Lengthen the stitch length setting. S-10
Wrong presser foot was used. Use the correct presser foot.
S-68
Needle is turned, bent or the point is dull. Replace the needle. B-51
Thread is entangled. Cut the entangled thread and remove it from
the race.
A-11
Fabric puckers There is a mistake in the upper or bobbin
threading.
Check the steps for threading the machine
and rethread it correctly.
B-39, B-42
Thread tension is set incorrectly. Adjust the thread tension. S-12
Stitches are too long when sewing thin fabrics. Shorten the stitch length. S-10
Needle is turned, bent or the point is dull. Replace the needle. B-51
Spool cap is set incorrectly. Check the method for attaching the spool
cap, then reattach the spool cap.
B-42
Wrong presser foot. Use the correct presser foot.
S-68
Problem Cause Solution Page
205


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Crescendo BLCR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Crescendo BLCR in the language / languages: English as an attachment in your email.

The manual is 12,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Crescendo BLCR

Baby Lock Crescendo BLCR Quick start guide - English, French, Spanish - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info