525694
204
Zoom out
Zoom in
Previous page
1/216
Next page
TROUBLESHOOTING
A-14
List of Symptoms
Problem Cause Solution Page
The thread is tangled
on the wrong side of
the fabric.
Upper threading is incorrect. Check the steps for threading the machine
and rethread the machine.
B-42
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle
Combinations” chart.
B-53
The upper thread is
too tight.
The bobbin thread is incorrectly installed. Correctly install the bobbin thread. B-39
Cannot thread the
needle
Needle is not in the correct position. Press the “Needle Position” button to raise
the needle.
B-13
Needle is installed incorrectly. Reinstall the needle correctly. B-51
Needle is turned, bent or the point is dull. Replace the needle. B-51
Cannot lower the
presser foot with the
presser foot lever
Presser foot was raised using the “Presser Foot
Lifter” button.
Press the “Presser Foot Lifter” button to
lower the presser foot.
B-13
Thread tension is
incorrect
Upper threading is incorrect. Check the steps for threading the machine
and rethread the machine.
B-42
Bobbin is set incorrectly. Reset the bobbin. (If needle plate was
removed, reinstall needle plate and tighten
screws prior to installing bobbin case.)
B-39
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle
Combination” chart.
B-53
Presser foot holder is not attached correctly. Reattach the presser foot holder correctly. B-49
Thread tension is set incorrectly. Adjust the thread tension. S-12
Bobbin thread is incorrectly wound. Use a correctly wound bobbin. B-34
Needle is turned, bent or the point is dull. Replace the needle. B-51
Upper thread breaks Machine is not threaded correctly (used the
wrong spool cap, spool cap is loose, the thread
did not catch the needle bar threader, etc.)
Rethread the machine correctly. B-42
Needle is turned, bent or the point is dull. Replace the needle. B-51
There are scratches on the bobbin case. Replace the bobbin case, or consult your
authorized retailer.
A-3
Upper thread tension is too strong. Adjust the thread tension. S-12
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle
Combinations” chart.
B-53
Thread is twisted. Use scissors, etc., to cut the twisted thread
and remove it from the race, etc.
There are scratches near the hole of the needle
plate.
Replace the needle plate, or consult your
authorized retailer.
S-26
There are scratches near the hole in the presser
foot.
Replace the presser foot, or consult your
authorized retailer.
B-49
Needle is installed incorrectly. Reinstall the needle correctly. B-51
Thread is knotted or tangled. Rethread upper and lower thread. B-39, B-42
A bobbin designed specifically for this machine
is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
B-39
Bobbin thread breaks Bobbin is set incorrectly. Reset the bobbin thread correctly. B-39
There are scratches on the bobbin or it doesn’t
rotate properly.
Replace the bobbin. B-39
Thread is twisted. Use scissors, etc. to cut the twisted thread
and remove it from the race, etc.
A bobbin designed specifically for this machine
is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
B-39
Bobbin thread does
not wind neatly on the
bobbin.
The thread is not passed through the bobbin
winding thread guide correctly.
Correctly pass the thread through the bobbin
winding thread guide.
B-35
Bobbin spins slowly. Press [+] in the bobbin winding window to
increase the bobbin winding speed.
B-37
The thread that was pulled out was not wound
onto the bobbin correctly.
Wind the thread that was pulled off around
the bobbin 5 or 6 times clockwise.
B-36
204


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Crescendo BLCR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Crescendo BLCR in the language / languages: English as an attachment in your email.

The manual is 12,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Crescendo BLCR

Baby Lock Crescendo BLCR Quick start guide - English, French, Spanish - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info